background image

1 – Introduction

General Public License

1-10

59225-00 B

S

You may charge a fee for the physical act of transferring a copy, and you 
may at your option offer warranty protection in exchange for a fee.

3.

You may modify your copy or copies of the Program or any portion of it, thus 
forming a work based on the Program, and copy and distribute such 
modifications or work under the terms of Section 1 above, provided that you 
also meet all of these conditions:
a.

You must cause the modified files to carry prominent notices stating 
that you changed the files and the date of any change.

b.

You must cause any work that you distribute or publish, that in whole or 
in part contains or is derived from the Program or any part thereof, to 
be licensed as a whole at no charge to all third parties under the terms 
of this License.

c.

If the modified program normally reads commands interactively when 
run, you must cause it, when started running for such interactive use in 
the most ordinary way, to print or display an announcement including 
an appropriate copyright notice and a notice that there is no warranty 
(or else, saying that you provide a warranty) and that users may 
redistribute the program under these conditions, and telling the user 
how to view a copy of this License. (Exception: if the Program itself is 
interactive but does not normally print such an announcement, your 
work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable 
sections of that work are not derived from the Program, and can be 
reasonably considered independent and separate works in themselves, then 
this License, and its terms, do not apply to those sections when you 
distribute them as separate works. But when you distribute the same 
sections as part of a whole which is a work based on the Program, the 
distribution of the whole must be on the terms of this License, whose 
permissions for other licensees extend to the entire whole, and thus to each 
and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to 
work written entirely by you; rather, the intent is to exercise the right to 
control the distribution of derivative or collective works based on the 
Program. 

In addition, mere aggregation of another work not based on the Program 
with the Program (or with a work based on the Program) on a volume of a 
storage or distribution medium does not bring the other work under the 
scope of this License.

4.

You may copy and distribute the Program (or a work based on it, under 
Section 2) in object code or executable form under the terms of Sections 1 
and 2 above provided that you also do one of the following: 
a.

Accompany it with the complete corresponding machine-readable 
source code, which must be distributed under the terms of Sections 1 

Summary of Contents for SANbox 1400 Series























































































































































































































Reviews: