Qlogic SANbox 3810 Interface Manual Download | Manualshive

Page: 197 / 396

background image

Command Reference

Group

59270-00 A

13-29

A

list

Displays a list of all groups and the security sets of which they are members. This
keyword is available without an Admin session.

members [group]

Displays all members of the group given by [group]. This keyword is available
without an Admin session.

remove [group] [member_list]

Remove the port/device worldwide name given by [member] from the group given
by [group]. Use a <space> to delimit multiple member names in [member_list]

rename [group_old] [group_new]

Renames the group given by [group_old] to the group given by [group_new].

securitysets [group]

Displays the list of security sets of which the group given by [group] is a member.
This keyword is available without an Admin session.

type [group]

Displays the group type for the group given by [group]. This keyword is available
without an Admin session.

Notes

Primary and secondary secrets are not included in a switch configuration backup.
Therefore, after restoring a switch configuration, you must re-enter the primary
and secondary secrets. Otherwise, the switch will isolate because of an
authentication failure.

Refer to the

“Securityset” command on page 13-77

for information about

managing groups in security sets.

Binding
(ISL Groups)

1

Domain ID of the switch to which to bind the ISL group mem-
ber worldwide name. This option is available only if
FabricBindingEnabled is set to True using the

Set Config Security

command. 0 (zero) specifies no binding.

1

SANbox 3810 switches do not support ISL groups.

Table 13-5. Group Member Attributes (Continued)

Attribute

Description

«
...
195
196
197
198
199
...
»

Summary of Contents for SANbox 3810













































































































































































































































































































































































































Reviews:

No comments

Related manuals for SANbox 3810

MCD-LED17 series

Brand: Raritan Pages: 89

Brand: Avenview Pages: 10

Brand: ALFAtron Pages: 15

Brand: Lockly Pages: 12

Brand: Manhattan Pages: 4

Brand: Wetekom Pages: 34

8265 Nways ATM Switch

Brand: IBM Pages: 100

IMI Sensors 691A80

Brand: PCB Piezotronics Pages: 15

Brand: Qvis Pages: 7

Brand: Justin Pages: 8

Brand: Scion-Tech Pages: 9

Brand: Novy Pages: 12

Brand: Netis Pages: 8

Cutler-Hammer NTV Series

Brand: Eaton Pages: 28

302523/20191008SZ114

Brand: Primewire Pages: 12

ExtremeSwitching 3600 Series

Brand: Extreme Networks Pages: 51

Brand: Freestyle Pages: 5

Brand: Keysight Technologies Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands