Qlogic SANbox 3810 Interface Manual Download

Page: 45 / 396

Network Configuration

Managing IP Security

59270-00 A

3-15

Creating an Association

To create an association, enter the

Ipsec Association

Create command as shown

in the following example:

SANbox #> admin start

SANbox (admin) #> ipsec edit

SANbox (admin-ipsec) #> ipsec association create h2h-sh-sa

A list of attributes with formatting will follow.

Enter a value or simply press the ENTER key to skip specifying a value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

Required attributes are preceded by an asterisk.

Value (press ENTER to not specify value, 'q' to quit):

Description (string value, 0-127 bytes) : Host-to-host: switch->host

*SourceAddress (hostname, IPv4, or IPv6 Address) : fe80::2c0:ddff:fe03:d4c1

*DestinationAddress (hostname, IPv4, or IPv6 Address) : fe80::250:daff:feb7:9d02

*Protocol (1=esp, 2=esp-old, 3=ah, 4=ah-old) : 1

*SPI (decimal value, 256-4294967295) : 333

Authentication (select an authentication algorithm)

1=hmac-md5 (16 byte key)

2=hmac-sha1 (20 byte key)

3=hmac-sha256 (32 byte key)

4=aes-xcbc-mac (16 byte key)

authentication algorithm choice : 2

*AuthenticationKey (quoted string or raw hex bytes) : "12345678901234567890"

*Encryption (select an encryption algorithm)

1=des-cbc (8 byte key)

2=3des-cbc (24 byte key)

3=null (0 byte key)

4=blowfish-cbc (5-56 byte key)

5=aes-cbc (16/24/32 byte key)

6=twofish-cbc (16-32 byte key)

encryption algorithm choice : 2

*EncryptionKey (quoted string or raw hex bytes) : "123456789012345678901234"

The security association has been created.

This configuration must be saved with the 'ipsec save' command

before it can take effect, or to discard this configuration

use the 'ipsec cancel' command.

Summary of Contents for SANbox 3810













































































































































































































































































































































































































Search results

Summary of Contents for SANbox 3810

Reviews:

Related manuals for SANbox 3810

Brands by name

Popular brands

Qlogic SANbox 3810, Interface Manual

Search results

Summary of Contents for SANbox 3810

Reviews:

Related manuals for SANbox 3810

Brands by name

Popular brands