background image

3

Warnings

QM-1000 manual

Warning

, constant exposure to high ambient 

sound pressure levels will cause hearing damage. 

Exposure to extremely high noise levels over 

long periods of time will cause permanent 

hearing loss.

Many countries have Government occupational 

safety authorities and the following noise table 

is a commonly agreed standard of permissible 

noise level exposures a worker can be subjected 

to without suffering great hearing loss.

duration Per day (Hrs)

Sound level dB  

(A weighted scale)

90

92

95

97

100

½

 

102

105

½

 

110

¼ or less 

115

Any exposure in excess of the above permissible 

limits could result in some hearing loss.

You will notice a rapid increase in hearing 

damage above 103dB. Apart from the sound 

pressure level of the sound system, you have 

the added effect of people yelling into your 

ear to he heard over the volume of the sound 

system. Hearing damage can not be reversed so 

limit the time you are in loud environments or 

buy ear plugs. 

Be protected by hearing protection such as ear 

plugs. In the case of audio mixing personnel, 

remove the plugs when you are mixing and 

replace them if you are between music sets. 

This will lower your exposure time to high SPL. 

Safety precautions

Quest Engineering strongly advise 

unless you possess skill in the proper 

use of hand and power tools and 

have a thorough understanding of 

local building and fire codes, then the 

installation of this speaker should 

be carried out by suitably qualified 

personnel following locally authorised 

and approved safety standards. A 

familiarity with the area behind the 

wall or ceiling where you plan to 

install the speakers is extremely 

important. Improper installation can 

cause serious injury or death. If in 

doubt contact your Quest Engineering 

dealer or a professional installation 

technician.

Installation allowing direct  precipitation 

is not advised and installation practise 

must prevent liquids from entering the 

speaker enclosure.

Do not place sources of heat on the 

speaker cabinet such as lighting 

equipment or smoke machines, and 

where possible please keep out of 

direct sunlight.

Attention

Before connecting or operating your 

new Quest Engineering speaker, please 

study the accompanying instruction 

manual paying particular attention to 

the operating precautions and wiring 

procedure.

Quest Engineering will not assume 

responsibility for incorrect installation 

or operation of this product.

Summary of Contents for QM 1000AS

















Reviews: