background image

QUAD195/D 

RF Gain: 

1.5 dB 

RF Output: 

Four outputs, 50 Ohm, BNC 

Filtering: 

Two section helical resonator 

Third Order Intercept: 

+25 dBm 

Power Input: 

12 to 20 Vdc (either polarity) 

Pins 1 and 4 on XLR power jack 

CH-50 adapter for AC operation 

14 to 20 Vac, 50/60 Hz, 1/2 Amp 

Pins 2 and 3 on XLR power jack 

16 to 22 Vdc 1/2 Amp 

Power Consumption: 

45 mA (plus 55 mA for each CR187 receiver) 

Total 265 mA 

Connectors: 

RF: BNC 

POWER INPUT: 4 pin XLR (Switchcraft D4M) 

POWER OUTPUT: 2.5mm power jack 

A/D Electronics part # ADC-014 

Short Circuit Protection: 

Auto-reset thermal fuses (6) 

MECHANICAL ASSEMBLY 
Construction: 

Machined aluminum panels, housings, and mechanical parts. 

Dimensions: 

6 x 8 x 9 inches (in carrying case) 

Weight: 

14.25 lbs including 4 CR187 receivers 

Batteries: 

Two 6V, 4.8 Ah rechargeable gel-cells 

Panasonic LCR-456-P 

Operating Time per Charge: 

14.5 Hours 

Specifications subject to change without notice. 

SERVICE AND REPAIR 

If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment 

needs repair.  Make sure you have followed the setup procedure and operating instructions.  Check out the intercon­

necting cords and then go through the TROUBLE SHOOTING section in the manual 

Summary of Contents for 195D











Reviews: