background image

Page 11

 

250-6103C   December 6, 2004

3100 ACT Wood Stove Series

R

FIGURE 11B

SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE

For the method of installation to a masonry chimney shown in 

Figures 13A & 13B on page 13

, it will be necessary to 

purchase a 12” (305mm) long 8" (203mm) inside diameter, section of prefabricated listed solid pack chimney to use as a 
thimble.  Purchase a wall spacer, trim collar, and a wall band manufactured to fit the chimney section you purchase.

The safety features of this system are two fold:  1) A 2" (51 mm) air space between the chimney section and combustible wall; 
and, 2) The 1" (25mm) air space around the chimney connector as it passes through the chimney section to the chimney.

The  location  of  the  opening  through  the  wall  to  the  chimney  must  leave  a  minimum  18"  (457mm)  vertical  clearance 

between  the  connector  pipe  and  the  ceiling  (or  minimum  recommended  from  pipe  manufacturer)  to  prevent  the 
ceiling from catching fire.

Measure for the center-line as shown in 

Figure 11A 

below.  Cut an opening in the wall large enough to accommodate the 

outside dimension of the chimney section plus the minimum air space specified by its manufacturer.  It may be necessary 
to cut the wall studs and install a header and a sill frame to maintain the wall support.  The hole in the chimney must have 
at least an 8" (203mm) diameter fire clay liner or equivalent, secured with refractory mortar.  If it is necessary to cut a hole 
in the chimney liner, use extreme care to keep it from shattering.

FLOOR 

PROTECTOR

THIMBLE,

12" (305mm) 

OF BRICK

CEILING 

JOIST

COMBUSTIBLE 

WALL

1" (25mm) 

CLEARANCE

AIRTIGHT 

CLEANOUT DOOR

FIRECLAY FLUE 

LINER WITH AIR 

SPACE

SHEATHING

EAVE

1" (25mm) CLEARANCE 

WITH FIRESTOP

RAFTER

FLASHING

CONCRETE CAP

WARNING!  ALWAYS FOLLOW CHIMNEY CONNECTOR MANUFACTURER’S INSTRUCTIONS FOR PROPER INSTALLATION.

CHIMNEY CONNECTOR IS TO BE USED ONLY WITHIN THE ROOM, BETWEEN THE STOVE AND CEILING OR WALL, NEVER 

PASSING THROUGH A COMBUSTIBLE CEILING OR WALL.  THE CONNECTOR SHALL NOT PASS THROUGH AN ATTIC OR 

ROOF SPACE, CLOSET OR SIMILAR CONCEALED SPACE, OR A FLOOR, OR CEILING.  MAINTAIN MINIMUM CLEARANCES 

TO COMBUSTIBLES AS REFERENCED ON PAGE 7.

Center of Hole

Wall

Center Line

Opening

Center Line

Add center-line measurement to depth 

measurement of your floor protector.  

Mark this combined measurement at 

correct wall location for your installa-

tion, maintaining minimum clearance 

to combustibles, and mark wall for a 

10" x 10" (254mm x 254mm) square 

hole. 

FIGURE 11A

Summary of Contents for 3100 Series





























Reviews: