background image

Page  4

7022-122D

May 12, 2014

Castile Pellet Insert

1

Listing and Code Approvals

A.  Appliance Certifi cation

C.  Glass Specifi cations

E.  BTU & Effi ciency Specifi cations

This appliance is equipped with 5mm ceramic glass. 

 

Replace glass only with 5mm ceramic glass.  Please contact 
your dealer for replacement glass.

This appliance is approved for mobile home installations 
when not installed in a sleeping room and when an outside 
combustion air inlet is provided.  

The structural integrity of the mobile home fl oor, ceiling, and 
walls must be maintained.  The appliance must be properly 
grounded to the frame of the mobile home and use only listed 
pellet vent, Class “L” or “PL” connector pipe.  

A Quadra-Fire Outside Air Kit must be installed in a mobile 
home installation.

B.  Mobile Home Approved

NOTE:  

This installation must conform with local codes. In 

the absence of local codes you must comply with the 

ASTM 

E1509-2004, ULC S628-93, ULC/ORD-C-1482-M1990, 
(UM) 84-HUD 

D.  Electrical Rating

115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps

MODEL:

Castile Pellet Insert-B

LABORATORY:

OMNI Test Laboratories, Inc

REPORT NO.

061-S-77d-6.2

TYPE:

Solid Fuel Room Heater/Pellet Fuel 
Burning Type Insert

STANDARD:

ASTM E1509-2004, ULC S628-93 and 
ULC/ORD-C1482-M1990 Room Heater 
Pellet Fuel Burning Type and (UM) 84-
HUD, Mobile Home Approved

NOTE:  

Hearth & Home Technologies, manufacturer of 

this appliance, reserves the right to alter its products, 
their specifi cations and/or price without notice.

WARNING! Risk of Fire! Hearth & Home Technologies dis-
claims any responsibility for, and the warranty and agency 
listing will be voided by the below actions.

DO NOT:
 

•  Install or operate damaged appliance

 • 

Modify 

appliance

 

•  Install other than as instructed by Hearth & Home 

Technologies

 

•  Operate the appliance without fully assembling all 

components

 • 

Overfi re

 

•  Install any component not approved by Hearth & 

Home Technologies

 

•  Install parts or components not Listed or approved.

 

•  Disable safety switches

Improper installation, adjustment, alteration, service or 
maintenance can cause injury or property damage. 

For assistance or additional information, consult a qualifi ed 
installer, service agency or your dealer.

Quadra-Fire is a registered trademark of Hearth & Home 
Technologies.

NOTE:  Some generator or battery back-up systems may 
not be compatible with the micro-processor electron-
ics on this appliance.  Please consult the power supply 
manufacturer for compatible systems.

The Castile Pellet Insrt by Quadra-Fire is exempt from Envi-
ronmental Protection Agency certifi cation  under 40 CFR 
60.531 y defi nition [Wood Heater (A) “Air to Fuel Ratio].

Note:

  

This appliance is also approved for installation 

into a shop.

*BTU output will vary, depending on the brand of fuel you 
use in your appliance.  Consult your Quadra-Fire dealer for 
best results.

Particulate 
Emissions Rating:

1.8 grams/hr

*BTU Output:

8,500 - 28,200 / hr

Heating Capacity:

up to 1,500 sq. ft. depending on 
climate zone

Hopper Capacity:

45 lbs

Fuel:

Wood Pellets or Shelled Corn

Shipping Weight:

214 lbs

Effi ciency

78%

These heaters meet the US Environmental Protection 
Agency’s emissions limits for pellet heaters. Under specifi c 
conditions the PS35 stove has been shown to deliver heat 
at rates ranging from 8,500 to 28,200 BTU/hr.

Summary of Contents for CASTILEI-MBK

























































Reviews: