background image

May 12, 2014

7022-122D

Page  41

Castile Pellet Insert

11

Reference Materials

shut off power to the appliance.

7. Heat Exchangers

The heat exchangers transfer heat from the exhaust system 
into convection air.  There are 2 clean out rods located under 
the heat exchangers.

8.   Heat Output Switch

The heat output switch is located on the lower right side of 
fi rebox, behind the front access door and above the reset 
button.  The function of the heat output switch is to regulate 
the burn rates; low, medium and high settings.

9. Hopper 

Switch

The hopper switch is located in the upper right hand corner, 
outside of the hopper.  This switch is designed to shut down 
the feed motor whenever the hopper lid is opened.

10. Igniter

The igniter is mounted on the base of the fi repot.  Combustion 
air travels over the red hot igniter creating super heated air 
that ignites the pellets. 

11.  Junction Box And Wiring Harness

The junction box is located on the lower right side of the 
appliance, behind the left front access door.  The junction box 
and wiring harness are replaced as one component.

12. Power Supply

The power outlet is located on the lower right side of the 
appliance on the front of the junction box.  Check the wall 
receptacle for 120 volt, 60 Hz (standard current).  Make sure 
the outlet is grounded and has the correct polarity.  A good 
surge protector is recommended.  When operating with a 
generator you need a least 600 watts of power, or with an 
inverter at least 800 watts of power available for the appliance 
during the start cycle.

13.  Red Call Light

The red call light is on the top of the junction box by the 
fuse.  The function of the red call light is to indicate that the 
thermostat is calling for heat.

14. Reset Button

The reset button is located on the lower right side of fi rebox 
in behind the access door and below the heat output control 
switch.  The function of the switch is to momentarily open the 
thermostat circuit, which restarts the system.  

15. Thermocouple

The thermocouple is located on top of the fi repot  inside 
the thermocouple cover (ceramic protection tube). The 
thermocouple sends a millivolt signal to the control box 
indicating the preset temperatures of the green and red lights 

When describing the location of a component 

part it is always AS YOU FACE THE FRONT 

OF THE APPLIANCE.

2. Convection Blower

The convection blower is mounted at the bottom rear of the 
appliance.  There are 2 impellers, one on each side of the 
motor.  The convection blower pushes air through the heat 
exchange system into the room.  

3. Exhaust Blower

The exhaust blower is mounted on the right side of the 
appliance behind the right side panel.  The exhaust blower 
is designed to pull the exhaust from the appliance and push 
it out through the venting system.  

4. Feed System

The feed system is located behind the fi rebox and can be 
removed as an entire assembly.  The assembly includes 
the feed motor, mounting bracket, bearing and feed spring 
(auger).  The hollow feed spring (auger) pulls pellets up the 
feed tube from the hopper area and drops them down the 
feed chute into the fi repot at a set rate. The feed motor starts 
and stops every 7 seconds. 

5. Firepot

The  fi repot is made of high quality ductile iron and has a 
cleaning pull-out rod.  The fl oor of the fi repot opens for 
cleaning when you pull out the rod.  Be sure that the fl oor 
returns to a completely closed position or your appliance 
will not operate properly.

6. Fuse

The fuse is located on the side of the junction box near the 
red call light.  The fuse will blow should a short occur and 

NOTE:

Do 

NOT

 open the control box.  This will void the 

warranty.  If you need to plug in or remove the control 
box you must fi rst

 unplug the appliance.

1. Control Box

 

a.  The control box is located on lower right side of 

appliance, on top of the junction box.

 

b. There is a  light located inside of the control box. The 

internal light will turn green when the appliance has 
reached a temperature of 200

F (93

C) in the fi repot. 

and will turn red when it reaches 600

o

F (315

C).

 

c.  There is also an internal blue light located in the upper 

left corner of the control box.  When you plug in the 
appliance the blue light will automatically start blinking 
4 blinks every 10 seconds for 60 seconds (depending 
upon setting) and then will stop. 

A. Component Function

Summary of Contents for CASTILEI-MBK

























































Reviews: