14
7027-802K
10/21
Q. Thermostat Temperature Programs
The thermostat by default has 4 separate program events
they are: MORN, DAY, EVE, and NITE. Each event ends at
the start time of the following event.
NOTE:
When the last event is finished for each day or
group of days, the thermostat will advance forward into
the next day or group of days.
NOTE:
If the thermostat is set for 2 events a day instead
of 4, the thermostat will only use the DAY and NITE
events.
R. Thermostat Other Features
TEMPERATURE CALIBRATION:
The internal temperature sensor in this thermostat is
accurately calibrated at the factory, and in most cases
alterations to this setting should not be needed. The
temperature calibration feature allows you to manually offset
the measured temperature by as much as plus or minus 5°F
(3°C) from its original value. If several thermostats are used
in the same house, this feature can be used to synchronize
this thermostat to the others.
Change the temperature calibration:
1. Move TEMPERATURE switch to OFF.
2. Move SET switch to RUN.
3. Press and hold both UP and DOWN buttons together for
at least 5 seconds; the words SET and CAL will appear
on the display along with a single flashing temperature
digit.
4. Use the UP or DOWN buttons to change the number of
degrees desired for adjustment; 0° is the default value
and also means no correction will be applied.
5. Press the NEXT button to accept the setting.
KEYPAD LOCKOUT:
There is the option to lock the front panel buttons to prevent
unauthorized tampering of your thermostat settings.
To Lock the Keypad:
1. Move TEMPERATURE switch to HEAT.
2. Move SET switch to RUN.
3. Perform a single press of each button in the
following sequence:
• NEXT, NEXT, NEXT, HOLD
A padlock will appear on the display screen.
To Unlock the Keypad:
1. Move TEMPERATURE switch to HEAT.
2. Move SET switch to RUN.
3. Perform a single press of each button in the
following sequence:
• NEXT, NEXT, NEXT, HOLD
A padlock will no longer be present on the display screen.
NOTE:
All other features need to be completed in a timely
manner as the thermostat will time out after 10 seconds.
NOTE:
The word COPY will not appear on the display
for Monday, but will display each day afterwards for
approximately one second and the day of the week will
automatically advance forward to the next day.
TEMPERATURE HOLD:
Temperature hold is used for maintaining a fixed set
temperature; once a HOLD is initiated, the thermostat will
maintain the set temperature indefinitely. To enter a HOLD
state, press the HOLD button one time and the word HOLD
will appear on the display. To cancel, press the HOLD button
once again.
6. Use steps 3 through 5 to set up the events for the rest of
the week or group of days.
7. Return the SET switch back to RUN.
COPY PROGRAM FEATURE:
Using similar instructions as set temperature programs the
COPY button will allow a whole day of set program events
to be copied to another day.
1. Move Temperature switch to HEAT as well as move SET
switch to TEMP PROG position.
2. Starting with Monday, use the UP or DOWN buttons to
adjust the start time and set temperature for the MORN,
DAY, EVE, and NITE events. Press the COPY button
and then press the NEXT button to advance to Tuesday.
3. With Tuesday displayed press COPY button. As
all programs events from Monday will be copied to
Tuesday (this will advance automatically to the next
day; Wednesday, as the word COPY will appear on the
screen for one second).
SET TEMPERATURE PROGRAMS:
1. Move TEMPERATURE switch to HEAT.
2. Move SET switch to TEMP PROG position.
3. Starting with Monday, use the UP or DOWN buttons to
adjust the start time and set temperature for the MORN
event, and then press NEXT button to advance.
4. Adjust the start time and set temperature of the DAY
event then press NEXT button.
5. Continue in this same manner to adjust the start time
and set temperatures for the EVE and NITE events
for Monday
Thermostat is protected against normal static electric
discharges, however to minimize the risk of damaging
the thermostat in extremely dry weather, please touch a
grounded metal object before touching the thermostat.
STATIC NOTICE
4. Continue in this pressing COPY button to set desired
days with original setting.
