background image

November 30, 2017 

 

 

 

 

7014-259B 

 

 

 

         

                  5

CB1200 FREESTANDING

WARRANTY CONDITIONS:

•  This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of 

HHT authorized dealers is available on the HHT branded websites.

•  This warranty is only valid while the HHT appliance remains at the site of original installation.

•     This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance 

resides.

•  Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact 

the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service 

from a dealer other than the dealer from whom you originally purchased the product.

•  Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges 

for parts are not covered by this warranty.

This warranty is void if:

•  The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging 

chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, 

cracking and discoloration of steel or enamel finishes.

•  The appliance is subjected to prolonged periods of dampness or condensation.

•  There is any damage to the appliance or other components due to water or weather damage which is the result of, but 

not limited to, improper chimney or venting installation.

LIMITATIONS OF LIABILITY:

•  The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or 

implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no 

event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states 

do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. 

This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO 

THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY 

SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE 

EXPRESSED WARRANTY SPECIFIED ABOVE.

WARRANTY EXCLUSIONS:

This warranty does not cover the following:

•  Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and 

exterior surface finishes may occur. This is not a flaw and is not covered under warranty.

•  Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items, 

or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.

•  Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts 

include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.

•  Expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints 

related to this noise are not covered by this warranty.

•  Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation 

instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to 

install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper opera-

tion, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/ 

incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting 

caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or 

forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7) 

installation or use of components not supplied with the appliance or any other components not expressly authorized 

and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing; 

and/or (9) interruptions or fluctuations of electrical power supply to the appliance.

•  Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.

•  Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.

•  HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa-

tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-

ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of 

the structure.

4021-645H   10/15 

Page 2 of 2

Summary of Contents for CB1200M-MBK





































Reviews: