background image

R

COLUMBIA BAY

DIRECT VENT GAS APPLIANCE

Owner’s Manual

Installation and Operation

Model: 

COLBAY-FS-B

O-T L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

DO NOT DISCARD THIS MANUAL

CAUTION

•  Important  operating  and 

maintenance  instructions 

included.

•  Leave  this  manual  with 

party  responsible  for  use 

and operation.

•  Read,  understand  and 

follow these instructions 

for safe installation and 

operation.

•  Do not store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of this 

or any other appliance.

 

-  Do  not  try  to  light  any  appliance. 

Do not touch any electrical switch. Do not 

use any phone in your building.

-  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions.

-  If you cannot reach your gas supplier, call 

the fi re department.

•  Installation and service must be performed 

by a qualifi ed installer, service agency, or the 

gas supplier.

fi

 re 

This  appliance  may  be  installed  as  an  OEM  installation  in 

manufactured home (USA only) or mobile home and must be 

installed in accordance with the manufacturer's instructions and 

the manufactured home construction and safety standard,

 Title 

24 CFR, Part 3280 or Standard for Installation in Mobile Homes, 

CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated 

on the rating plate.

Installation and service of this appliance should be 

performed  by  qualifi ed  personnel.  Hearth  &  Home 

Technologies suggests NFI certifi ed or factory-trained 

professionals, or technicians supervised by an NFI 

certifi ed professional.

DO NO

T

DISCARD

In the Commonwealth of Massachusetts:

•  installation must be performed by a licensed plumber or gas 

fi tter.

See Table of Contents for additional Commonwealth of Mas-

sachusetts requirements.

Page  1

Quadra-Fire  •  COLBAY-FS-B  •  250-5195 Rev. R  •  10/11

HOT SURFACES

!

Glass and other surfaces are hot during 

operation AND cool down.

•  Do not touch glass until it is cooled

•  NEVER allow children to touch glass

•  Keep children away

•  CAREFULLY  SUPERVISE  children  in  same  room  as 

fi replace.

•  Alert children and adults to hazards of high temperatures.

fl

•  Keep  clothing,  furniture,  draperies  and  other  fl ammable 

materials away.

Summary of Contents for COLBAY-FS-B















































Reviews: