Quadra-Fire EXPIII-MBK-APAC Installation Manual Download

Page: 4 / 24

7060-801A

April 26, 2019

Explorer III AU Wood Appliance

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualified

installer, service agency or your dealer.

Hearth & Home Technologies WILL NOT warranty

appliances that exhibit evidence of over-firing. Evidence

of over-firing includes, but is not limited to:

•

Warped air tube

•

Deteriorated refractory brick retainers

•

Deteriorated baffle and other interior components

C. Glass Specifications

This appliance is equipped with 5mm ceramic glass.

Replace glass only with 5mm ceramic glass. Please

contact your dealer for replacement glass.

D. Non-Combustible Materials

Material which will not ignite and burn, composed of any

combination of the following:

- Steel

- Plaster

- Brick

- Iron

- Concrete

- Tile

- Glass

- Slate

E. Combustible Materials

Material made of/or surfaced with any of the following

materials:

Wood

- Compressed Paper

Plant Fibers

- Plastic

- Plywood/OSB

Sheet Rock (drywall)

Any material that can ignite and burn: flame proofed or not,

plastered or non-plastered.

• Installation and use of any damaged appliance.

•

Modification of the appliance.

•

Installation other than as instructed by Hearth &

Home Technologies.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

•

Operating appliance without fully assembling

all components.

• Operating appliance without legs attached (if

supplied with unit).

•

Do NOT Over fire

- If appliance or chimney connector

glows, you are over firing.

Any such action that may cause a fire hazard.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

NOTE:

Hearth & Home Technologies, manufacturer

of this appliance, reserves the right to alter

its products, their specifications and/or price

without notice.

Summary of Contents for EXPIII-MBK-APAC

























Search results

Summary of Contents for EXPIII-MBK-APAC

Reviews:

Related manuals for EXPIII-MBK-APAC

Brands by name

Popular brands

Quadra-Fire EXPIII-MBK-APAC, Installation Manual

Search results

Summary of Contents for EXPIII-MBK-APAC

Reviews:

Related manuals for EXPIII-MBK-APAC

Brands by name

Popular brands