background image

August 

13, 

2018     7061-197P 

     

13

Explorer II

D. Chimney Height / Rise and Run

This product was designed for and tested on a 6 inch 

(152mm) chimney, 14 to 16 feet (420-480cm) high, 

(includes appliance height) measured from the base of the 

appliance.  The further your stack height or diameter varies 

from this configuration,  the greater the likelihood it may 

affect performance.

Chimney height may need to be increased by 2 - 3% per 

each 1000 feet above sea level.  It is not recommended to 

use offsets or elbows at altitudes above 4000 feet above 

sea level or when there are other factors that affect flue 

draft.

Fire Risk

.

Inspection of Chimney:

•  Chimney must be in good condition.

•  Meets minimum standard of NFPA 211

•  Factory-built chimney must be 6 inch 

(152mm) UL103 HT.

WARNING

WARNING

Asphyxiation Risk.

• 

DO NOT CONNECT THIS Appliance TO A 

CHIMNEY FLUE SERVICING ANOTHER 

APPLIANCE.

• 

DO NOT CONNECT TO ANY AIR 

DISTRIBUTION DUCT OR SYSTEM.

May allow flue gases to enter the house.

Improper installation, adjustment, alteration, service or 

maintenance can cause injury or property damage. Refer 

to the owner’s information manual provided with this 

appliance. For assistance or additional information consult 

a qualified installer, service agency or your dealer.

WARNING

Floor

Protector

Chimney

Connector

Insulated " T "

Flashing

Listed Termination Cap

Trim Collar on

Inside Wall

Listed Chimney

Storm Collar

Wall Support

Roof Brace (if required)

Thimble

Figure 13.1 Prefabricated Exterior Chimney

E. Venting Components 

Chimney Connector:

It is also known as flue pipe or appliance pipe.  The 

chimney connector joins the appliance to the chimney.  It 

must be a 6 inch (152mm) minimum diameter 24 gauge 

mild steel black or 26 gauge blued steel, or an approved 

air-insulated double wall venting pipe.

  

Thimble

:  

A manufactured or site-constructed device installed in 

combustible walls through which the chimney connector 

passes to the chimney.  It is intended to keep the walls 

from igniting.  Site constructed thimbles must meet NFPA 

211 Standards.  Prefabricated must be suitable for use with 

selected chimney and meet UL103 Type HT Standards.  

Follow instructions provided by the manufacturer for 

manufactured thimbles for masonry chimney and 

prefabricated chimneys.

Chimney

:

The chimney can be new or existing, masonry or 

prefabricated and must meet the following minimum 

requirements and as specified in Section 4F.

NOTE: I

n Canada when using a factory-built chimney it 

must be safety listed,

 Type UL103 HT (2100oF) 

CLASS “A” 

or conforming to 

CAN/ULC-S629M, 

STANDARD FOR 650o

C FACTORY-BUILT 

CHIMNEYS.

F. Chimney Systems

Prefabricated Metal Chimney

• 

Must be minimum 6 inch (152mm) diameter (ID) high 

temperature chimney listed to UL 103 HT (2100

o

F) or 

ULC S629M.

•  Must use components required by the manufacturer for 

installation.

•  Must maintain clearances required by the manufacturer 

for installation.

•  Refer to manufacturers instructions for installation.

Summary of Contents for Explorer II series























Reviews: