background image

November 29, 2016 

 

 

 

 

 7060-228G 

 

 

 

         

                  19

Explorer III Wood Stove

Accessory List

Service Parts

Explorer III

Beginning Manufacturing Date: Feb 2015           

Ending Manufacturing Date: Active

R

IMPORTANT: THIS IS DATED INFORMATION

. Parts must be ordered from a dealer or 

distributor. 

Hearth and Home Technologies does not sell directly to consumers

. Provide 

model number and serial number when requesting service parts from your dealer or distributor.

Stocked 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

30

Baf

 e Assembly

SRV7060-025

30.1

Baf

 e Cover Top ( Includes Insulation Blanket ) 

SRV7060-238

30.2

Baf

 e Blanket

SRV7060-233

Y

30.3

Baf

 e Plate

SRV7060-250

30.4

Baf

 e Board

SRV7060-148

Y

30.5

Secondary Tubes

Qty 3 req

SRV7060-226

Y

30.6

Baf

 e Cover Plates

SRV7060-206

30.7

Baf

 e Linkage

SRV7060-044

31

Side Right

Matte Black

7060-033MBK

Porcelain Mahogany 7060-033PMH

Porcelain Dark Blue 7060-033PDB

Porcelain Black

7060-033PBK

Porcelain Frost

7060-033PFT

32

Manifold Gaskets

Qty 2 req

SRV7060-221

33

Air Supply Chambers

Right and Left

SRV7060-189

34

Pivot Tube Assemblies

Qty 2 req

SRV7060-018

35

Rear Baf

 e Plate

SRV7060-201

36

Baf

 e Board Rear 

SRV7060-213

37

Top Load Handle Hanger

SRV7060-262

Additional service part numbers appear on following page.

#30 Baf

 e Assembly

30.1

30.2

30.3

30.4

30.5

30.6

30.7

Summary of Contents for EXPLR-III-PBK





















Reviews: