background image

 6 

 

 

 

 

                       7060-228G 

 

 

 

       November 29, 2016

Explorer III Wood Stove

Appliance Install                                                                                              

Appliance is leveled and connector is secured to appliance.

Hearth extension size/height decided. 

Outside air kit installed.

Floor protection requirements have been met.

If appliance is connected to a masonry chimney, it should be cleaned and 

inspected by a professional. If installed to a factory built metal chimney, the 

chimney must be installed according to the manufacturer’s instructions and 

clearances. 

Chimney

Chimney installed, locked and secured in place with proper clearance. 

Chimney meets recommended height requirements (14-16 feet).

Terminations installed and sealed.

Clearances

Combustible materials not installed in non-combustible areas.

Mantels and wall projections comply with installation manual requirements. 
Protective hearth strips and hearth extension installed per manual requirements.

Appliance Setup

All packaging and protective materials removed. 

All labels have been removed from the door.

All packaging materials are removed from inside/under the appliance.

Manual bag and all of its contents are removed from inside/under the appliance

     and given to the party responsible for use and operation.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.

Customer:   __________________________________________________________________________

Date Installed: __________________________________________________________________________

Lot/Address:  __________________________________________________________________________

Location of Appliance: 

______________________________________________________________

Installer: 

__________________________________________________________________________

Dealer/ Distributor Phone #:  ______________________________________________________________

Serial #: 

__________________________________________________________________________

Model :             __________________________________________________________________________

 

WARNING! Risk of Fire or Explosion! 

Hearth & Home Technologies recommends the following:

• That this checklist remain visible at all times on the appliance until the installation is complete.

Comments: 

Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Comments communicated to party responsible                                                         by                                             on                    
 

 

   

          

(Builder/Gen. Contractor)                           (Installer)                        (Date)

YES       IF NO, WHY?

 

G. Install Checklist

Summary of Contents for EXPLR-III-PBK





















Reviews: