background image

 2 

 

 

 

 

                      

7061-197D 

 

 

 

         November 7, 2014

Explorer II Medium Wood Stove

TABLE OF CONTENTS

     Safety Alert Key:

• 

DANGER! 

Indicates a hazardous situation which, if not avoided will result in death or serious injury.

•  WARNING!

 Indicates a hazardous situation which, if not avoided could result in death or serious injury.

•  CAUTION! 

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• 

NOTICE:

 Indicates practices which may cause damage to the appliance or to property.

Quadra-Fire is a registered trademark of Hearth & Home Technologies.

Important Safety Information .............3

A.  Appliance Certifi cation ......................................................3
B.  BTU & Effi ciency Specifi cations........................................3
C.  Mobile Home Approved (USA ONLY) ............................... 3
D.  Glass Specifi cations .........................................................3
E. Non-Combustible Materials ...............................................3
F. Combustible Materials ........................................................3

Getting Started ....................................4

A. Design and Installation Considerations .............................4
B. Fire Safety .........................................................................4
C.  Negative Pressure ............................................................5
D.  Tools And Supplies Needed ..............................................5
E.  Inspect Appliance and Components .................................5
F. Install Checklist ..................................................................6

Dimensions and Clearances ..............7

A.  Appliance Dimensions ......................................................7
B. Clearances to Combustibles ..............................................8
C.  Locating Your Stove & Chimney .......................................9
D.  Chimney Termination Requirements ................................9
E.  2-10-3 Rule  ......................................................................10

Chimney Systems .............................11

A.  Venting Components  .......................................................11
B.  Chimney Systems .............................................................11
C. Installing Chimney Components ........................................13

Appliance Set-Up ..............................14

A.  Hearth Protection Requirements ......................................14
B. Outside Air Kit Installation  .................................................15
C.  Blower (Optional) ..............................................................16
D.  Reversible Flue Collar and Horizontal Flue Heat Shield ..17

Mobile Home Installation ..................18

Accessory List ..................................19

Summary of Contents for EXPLRMED-PBK





















Reviews: