background image

23

March 26, 2020

7039-802B

Figure 23.2

D. Door Handle Assembly

Service Part: SRV7039-008

1.  Install washer on door handle shaft.

2.  Slide door handle through door.

3. 

Install second washer(s) as shown in 

Figure 23.2

.

4.  Install key in groove.

5. 

Align groove in latch cam with key; slide latch cam 

over shaft

6. 

Install locknut but do not over tighten, the handle needs 

to move smoothly.

7.  Install spring handle turning in a counter-clockwise 

motion to required 2 inch (51mm) clearance location on 

door handle rod 

(Figure 23.2)

.

Magnet

Spade

Connectors

Snap Disc

Figure 23.1

C. Snap Disc

Service Part: SRV230-0470

1. 

Locate the snap disc bracket assembly at the bottom left 

rear corner of the appliance.

2. 

A magnet holds the bracket to the appliance. Pull the 

bracket down away from the appliance to expose the 

snap disc.

3.  Pull the snap disc and spade connectors up and out of 

bracket as shown in 

Figure 23.1

4.  Using a Phillips head screw driver, remove the 2 screws 

from the snap disc and then remove the snap disc from 

the spade connectors. Replace with new snap disc and 

re-connect to spade connectors.

5. 

Push the snap disc and spade connectors back inside 

bracket and re-attach the bracket to the appliance.

Locknut

Door Cross 

Section

Latch Cam

Spacing 

Washers

Square Key

Door Handle 

Shaft

Spring 

Handle

NOTE:

 DO NOT over tighten locking nut; door handle 

needs to move smoothly!

Summary of Contents for MILLENNIUM 2100 Series

































Reviews: