background image

October 12, 2017 

 

 

 

           7080-162B 

 

 

 

         

                  3

MT VERNON E2-C

The Quadra-Fire Mt. Vernon E2 Pellet Appliance meets the U.S. 

ENVIRONMENTAL PROTECTION AGENCY 

Certified  to  comply 

with 2020 particulate emission standards at 0.74 G/HR EPA CFR 

subpart AAA, using ASTM E2779-10, ASTM 2515-11 Method- 
Pellet Appliance sections, CSA B415.1-10

This pellet  appliance 

needs periodic inspection and repair for proper operation. It 

is against federal regulations to operate this pellet appliance 

in a manner inconsistent with the operating instructions in 

the owner’s manual.

Emissions Report Number: 0061PS094E

EPA Certification #:

98-17

EPA Certified Emissions:

0.74 g/hr

*LHV Tested Efficiency:

83.2%

**HHV Tested Efficiency:

77.9%

***EPA BTU Output: 12,682 - 39,428 / HR

****BTU Input: 16,396 - 50,775 / HR

Vent Size: 3 or 4, “L” or “PL”

Hopper Capacity: 80 lbs.

Fuel Wood Pellets

* Weighted average LHV efficiency using data collected during 

EPA emissions test.

**

Weighted average HHV efficiency using data collected during 

EPA emissions test.

***

A range of BTU outputs based on HHV and the burn rates from 

the low and high EPA tests.

****

Based on the maximum feed rate per hour multiplied by 

approximately 8600 BTU’s which is the average BTU’s from a 

pound of pellets.

Important Safety Information

NOTE:  Hearth & Home Technologies, manufacturer of this appli-

ance, reserves the right to alter its products, their specifications 

and/or price without notice.

Improper installation, adjustment, alteration, service or maintenance 

can cause injury or property damage. 

For assistance or additional information, consult a qualified installer, 

service agency or your dealer.

•  Installation and use of any damaged appliance. 

•  Modification of the appliance.

•  Installation other than as instructed by Hearth & Home 

Technologies.

•  Installation and/or use of any component part not approved by 

Hearth & Home Technologies.

•  Operating appliance without fully assembling all components.
•  Operating appliance without legs attached (if supplied with 

appliance).

•  Do NOT Over fire - If appliance or chimney connector glows, 

you are over firing.

Any such action that may cause a fire hazard.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any 

responsibility for, and the warranty will be voided by, 

the following actions: 

C. Glass Specifications

This appliance is equipped with 5mm ceramic glass.  

Replace glass only with 5mm ceramic glass.  Please con-

tact your dealer for replacement glass.

Model

Mt. Vernon Pellet Appliance E2

Laboratory

OMNI Test Laboratories, Inc.

Report No.

061-S-83-2

Type

Solid Fuel Room Appliance, Pellet Fuel Burn-
ing Type

Standard

ASTM E1509-12, ULC S627-00 and (UM) 

84-HUD, Mobile Home Approved.

FCC

Complies with Part 15 of FCC Rules. Opera-

tion is subject to the following two conditions:  

(1) this device may not cause harmful inter-

ference, and (2) this device must accept any 

interference received, including interference 

that may cause undesired  operation.

A. Appliance Certification

NOTICE:  

This installation must conform with local codes. In the 

absence of local codes you must comply with the 

ASTM E1509-

12, ULC S627-00, (UM) 84-HUD and  ULC/ORD-C-1482. 

B. BTU & Efficiency Specifications

D. Electrical Rating

115 VAC, 60 Hz, Start 2.9 Amps, Run 2.45 Amps

E. Mobile Home Approved

 • 

This appliance is approved for mobile home installa-

tions when not installed in a sleeping room and when 

an outside combustion air inlet is provided.

 • 

The structural integrity of the mobile home floor, ceil

-

ing, and walls must be maintained.  

 • 

The appliance must be properly grounded to the 

frame of the mobile home and use only Listed pellet 

vent Class “L” or “PL” connector pipe.  

 • 

Outside Air Kit, part OAK-3 must be installed in a mo-

bile home installation.

F.  Non-Combustible Materials

Material which will not ignite and burn, composed of any 

combination of the following: 

  - Steel 

- Plaster  

- Brick 

- Iron 

  - Concrete  - Tile 

- Glass 

- Slate

Materials reported as passing 

ASTM E 136, Standard 

Test Method for Behavior of Metals, in a Vertical Tube 

Furnace of 750° C. 

G. Combustible Materials

Material made of/or surfaced with any of the following 

materials: 

 

- Wood  

 

- Compressed Paper

 

- Plant Fibers   

- Plastic

 

- Plywood/OSB   

- Sheet Rock (drywall)

Any material that can ignite and burn: flame proofed or not, 

plastered or non-plastered. 

Summary of Contents for MT VERNON E2-C





























Reviews: