Quadra-Fire PELLET INSERT CB1200MI-MBK Installation Manual Download

Page: 1 / 32

7014-285A

October 9, 2017

CB1200 PELLET INSERT APPLIANCE

Model:

CB1200MI-MBK

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE: DO NOT DISCARD THIS MANUAL

NOTE

To obtain a French translation of this manual, please contact

your dealer or visit www.quadrafire.com

Pour obtenir une traduction française de ce manuel, s’il vous

plaît contacter votre revendeur ou visitez www.quadrafire.com

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recommends

HHT Factory Trained or NFI certified professionals.

WARNING

If the information in these instruc-

tions is not followed exactly, a

fire could result causing property

damage, personal injury, or death.

• Do not store or use gasoline or other flam

mable vapors and liquids in the vicinity of

this or any other appliance.

• Do not over fire - If appliance or chimney

connector glows, you are over firing. Over

firing will void your warranty.

• Comply with all minimum clearances to

combustibles as specified. Failure to

comply may cause house fire.

HOT SURFACES!

Glass and other surfaces are hot

during operation AND cool down.

Hot glass will cause burns.

•

Do not touch glass until it is cooled

•

NEVER allow children to touch glass

•

Keep children away

•

CAREFULLY SUPERVISE children in same room as

fireplace.

•

Alert children and adults to hazards of high temperatures

•

High temperatures may ignite clothing or other

flammable materials.

•

Keep clothing, furniture, draperies and other flammable

materials away.

WARNING

CAUTION

Tested and approved for wood pellets and corn pellets.

Burning of any other type of fuel voids your warranty.

CAUTION

Check building codes prior to installation.

• Installation MUST comply with local, regional, state and na

tional codes and regulations.

• Consult local building, fire officials or authorities having juris

diction about restrictions, installation inspection, and permits.

Summary of Contents for PELLET INSERT CB1200MI-MBK

































Search results

Summary of Contents for PELLET INSERT CB1200MI-MBK

Reviews:

Related manuals for PELLET INSERT CB1200MI-MBK

Brands by name

Popular brands

Quadra-Fire PELLET INSERT CB1200MI-MBK, Installation Manual

Search results

Summary of Contents for PELLET INSERT CB1200MI-MBK

Reviews:

Related manuals for PELLET INSERT CB1200MI-MBK

Brands by name

Popular brands