Quadra-Fire PELLET INSERT CB1200MI-MBK Installation Manual Download

Page: 30 / 32

7014-285A

October 9, 2017

CB1200 Pellet Insert
B. Accessory List

Service Parts

CB1200MI-MBK

Beginning Manufacturing Date: June 2009

Ending Manufacturing Date: Active

IMPORTANT: THIS IS DATED INFORMATION

. Parts must be ordered from a dealer or

distributor.

Hearth and Home Technologies does not sell directly to consumers

. Provide

model number and serial number when requesting service parts from your dealer or distributor.

Stocked

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

OPTIONAL ACCESSORIES

Adjustable Hearth Support - 12 in. X 50 in., 2-10 in. H

ADJSPT-12

Damper, 3 Inch - Tall Vertical Installs Only

PEL-DAMP3

Damper, 4 Inch - Tall Vertical Installs Only

PEL-DAMP4

Floor Protector

811-0730

Log Set Assembly

811-0592

Log, Rear Left

7050-144

Log, Rear Right

7050-143

Outside Air Kit

No longer available

811-0700

Hose, Alum Flex, 2 Inch X 3 Ft

3 Ft

SRV200-0860

Panel Set, Large, W/Gold Trim

33 in x 50 in.

SP-CB12I3350-GD

Bracket, -L-, Trim

Pkg of 2

832-0840

Logo, Quadra-Fire

Pkg of 10

7000-649/10

Trim, Panel Set, Gold

SRV250-4660

Panel Set, Large, W/Nickel Trim

33 in x 50 in.

SP-CB12I3350-NL

Bracket, -L-, Trim

Pkg of 2

832-0840

Logo, Quadra-Fire

Pkg of 10

7000-649/10

Trim, Panel Set, Ots, Nickel

510-5220

Panel Set, Large, W/Black Nickel Trim

33 in x 50 in.

SP-CB12I3350-NB

Bracket, -L-, Trim

Pkg of 2

832-0840

Logo, Quadra-Fire

Pkg of 10

7000-649/10

Trim, Panel Set, Ots, Nickel

7019-027

Panel Set, Small, W/Gold Trim

30 in. x 40 in.

SP-CB12I3040-GD

Bracket, -L-, Trim

Pkg of 2

832-0840

Logo, Quadra-Fire

Pkg of 10

7000-649/10

Trim, Panel Set, Std, Gold

811-0710

Panel Set, Small, W/Nickel Trim

30 in. x 40 in.

SP-CB12I3040-NL

Bracket, -L-, Trim

Pkg of 2

832-0840

Logo, Quadra-Fire

Pkg of 10

7000-649/10

Trim, Panel Set, Std, Nickel

510-5210

Panel Set, Small, W/Black Nickel Trim

30 in. x 40 in.

SP-CB12I3040-NB

Bracket, -L-, Trim

Pkg of 2

832-0840

Logo, Quadra-Fire

Pkg of 10

7000-649/10

Trim, Panel Set, Std, Nickel

7019-026

Handle, Pullrod

PULLROD-HNDL

Shroud, Rear

811-0680

Additional service part numbers appear on following page.

Summary of Contents for PELLET INSERT CB1200MI-MBK

































Search results

Summary of Contents for PELLET INSERT CB1200MI-MBK

Reviews:

Related manuals for PELLET INSERT CB1200MI-MBK

Brands by name

Popular brands

Quadra-Fire PELLET INSERT CB1200MI-MBK, Installation Manual

Search results

Summary of Contents for PELLET INSERT CB1200MI-MBK

Reviews:

Related manuals for PELLET INSERT CB1200MI-MBK

Brands by name

Popular brands