Quantech
11
Form QTC4-NM2
Issue date: 05/12/2023
1
Section 1 - General chiller information and safety
Introduction
Quantech QTC4 chillers are manufactured to the high-
est design and construction standards to ensure high
performance, reliability and adaptability to all types of
air conditioning installations.
The unit is intended for cooling water or glycol solu-
tions and is not suitable for purposes other than those
specified in this manual.
Ensure only a professional rigger does the rigging and
lifting, in accordance with a written rigging and lifting
plan. The most appropriate rigging and lifting method
depends on job specific factors, such as the rigging
equipment available and site needs. As a result, a pro-
fessional rigger must determine the rigging and lifting
method to be used, and it is beyond the scope of this
manual to specify rigging and lifting details.
This manual contains all the information required for
correct installation and commissioning of the unit, to-
gether with operating and maintenance instructions.
The manual must be read thoroughly before attempting
to operate or service the unit.
All procedures detailed in the manual, including in-
stallation, commissioning and maintenance tasks must
only be performed by suitably trained and qualified
personnel.
The manufacturer will not be liable for any injury or
damage caused by incorrect installation, commission-
ing, operation or maintenance resulting from a failure
to follow the procedures and instructions detailed in
the manual.
Warranty
Quantech warrants QTC4 chillers in accordance with
the Limited Warranty Engineered Systems Equipment
procedure. Refer to
Form 50.05-NM2
.
Quantech warrants all equipment and materials against
defects in workmanship and materials for a period of
eighteen months from date of shipment or 12 months
from date of startup, whichever comes first, unless la-
bor or extended warranty has been purchased as part
of the contract. The warranty is limited to parts only
replacement and shipping of any faulty part, or sub-
assembly, which has failed due to poor quality or man-
ufacturing errors. All claims must be supported by evi-
dence that the failure has occurred within the warranty
period, and that the unit has been operated within the
designed parameters specified.
All warranty claims must specify the unit model,
serial number, order number and run hours/starts. Mod-
el and serial number information is printed on the unit
identification plate.
The unit warranty is void if any modification to the
unit is carried out without prior written approval from
Quantech. For warranty purposes, the following condi-
tions must be satisfied:
• The initial start of the unit must be carried out by
trained personnel from an authorized Quantech
Service Center. See
Section 6 - Commissioning,
for more information.
• Only genuine Quantech approved spare parts,
oils, coolants, and refrigerants must be used.
• All the scheduled maintenance operations detailed
in this manual must be performed at the specified
times by suitably trained and qualified personnel.
See
Section 9 - Maintenance,
for more informa-
tion.
• Failure to satisfy any of these conditions au-
tomatically voids the warranty. Refer to
Form 50.05-NM2
for complete details.
The rigger must locate the center of
gravity through trial lifts to account
for possible variations in unit configura
-
tions. Contact your nearest Quantech
sales representative for weight data. See
Section 3 - Rigging, handling, and storage
on page 23 for more details.
Summary of Contents for QTC40160
