© Q I-201003 - BioShake iQ - Short Manual - rev005
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
Program
P1
(or
P2
)
activated
START
STOP
deactivate
Filling volume
96-well
(standard)
384-well
(standard)
384-well
(small-vol.)
1536-well
(standard)
10 %
1800 - 2200 rpm
2200 - 2600 rpm
2800 - 3000
2800 - 3000
25 %
1600 - 2000 rpm
2000 - 2400 rpm
2400 - 3000
2600 - 3000
50 %
1400 - 1800 rpm
1800 - 2200 rpm
2200 - 2600
2400 - 2600
75 %
1200 - 1600 rpm
1600 - 2000 rpm
2000 - 2400
2200 - 2600
Filling volume
0.2 ml tubes
0.5 ml tubes
1.5 ml tubes
2.0 ml tubes
25 %
1400 - 1800 rpm
1200 - 1600 rpm
1000 - 1300
1000 - 1300
50 %
1200 - 1500 rpm
1100 - 1300 rpm
1000 - 1200
900 - 1200
75 %
1000 - 1300 rpm
1000 - 1200 rpm
900 - 1100
900 - 1100
To Start press
P1
(or
P2
)
and hold for at
least 2 sec.
SAFETY
RECOMMENDED MIXING SPEEDS
For MICROPLATES depending on filling volume/well [%] for diluted fluids
For TUBES depending on filling volume/ well [%] for diluted fluids
Short press
P1
(or
P2)
PROGRAMMING P1 and P2
Delete program
Yes / No ?
e
g
n
a
h
C
values
with the
cursors!
Time
Change values with the
cursors as for progr. step I
Time Mix Temp.
Short press
P1
(or
P2)
to go forward
to the next
program step
Repeat STEP 4-5
for program
step II and
step III
To End press
P1
(or
P2
)
and hold for at
least 2 sec.
TO RUN THE PROGRAM
Short press
P1
(or
P2)
Short press
Short press
or
If you do not press Start/
Stop, the program will stop,
when it is finished.
Short press
P1
(or
P2)
IMPO RTANT NOTES:
Do not operate the device in rooms where work is being carried out with explosive substances.
•
Do not use this device to process any explosive, radioactive or highly reactive substances.
•
Do not use this device to process any substances, which could create an explosive atmosphere.
•
Danger! Electric shock from damage to device/ power cable. Danger! Lethal voltages inside the device.
•
Warning! General hazard point.
•
Warning! Injury from rapidly rotating holder. Injury from rapidly rotating imbalance compensation. Injury from flying tubes and plates.
•
Warning! Injury from sample material being flung out. Injury from incorrect vortexing.
•
Warning! Damage due to incorrect power supply.
•
Caution! Damage to the display from mechanical pressure. Severe vibration.
•
Caution! Damage to electronic components caused by spilled liquids. Damage to electronic components from condensation.
•
Caution! Poor safety due to missing operating manual. Caution when using aggressive chemicals.
•
Please start even with minimal mixing frequencies to avoid overloading.
•
O nly mix in sealed tubes and plates. Sample material can be flung out of open, inadequately sealed or unstable tubes and plates.
•
When working with hazardous, toxic and pathogenic samples, always comply with the nationally specified safety environment.
•
Pay particular attention to personal safety gear (gloves, clothing, glasses etc., the extraction hood and the safety class of the laboratory.
•
w w w . b u l l d o g - b i o . c o m
l
p h o n e : 6 0 3 - 5 7 0 - 4 2 4 8
l
f a x : 6 0 3 - 7 6 6 - 0 5 2 4
4 5 1 5 C u l v e r R o a d , S u i t e 3 0 7
|
R o c h e s t e r, N Y 1 4 6 2 2