background image

Read all wiring precautions. If you are not sure of the connections, contact

your authorized 

Quantum Audio

 dealer.

If you are using a source unit, without a remote turn-on lead, the 

QA3X

 can

be turned on with a switched accessory lead. You can find this accessory

power source in the factory harness at the back of the radio. It is the lead that

turns on and off with the key.

1.

 Before installation, make sure the source unit Power switch is in the OFF

position.

2.

 Disconnect the negative (-) lead of the battery before making any power

connections.

3.

A clean chassis ground connection is critical to the performance of your

Clarion crossover. Use the shortest ground wire possible and securely connect

to the car chassis to minimize resistance and avoid noise problems.

4.

 Refer to Figure 3 when making electrical connections.  Connect the

crossovers positive (+) lead via a fuse directly to the positive (+) terminal on

the battery. Use red-insulated 18-gauge (or larger) wire for the crossover’s

positive (+) power lead and the same-gauge black insulated wire for the

ground.

5.

To avoid noise problems, run the crossover’s positive (+) power lead and the

amplifier’s positive (+) power lead along one side of the vehicle to the battery.

.

Run the remote turn-on wire and RCA audio cables down the center and route

the speaker wires along the remaining side.  If wires must cross, run them

perpendicular to each other.

.

6.

 When creating passage holes for the power wire, use grommets to eliminate

any sharp edges created during drilling. This will protect the wire from being

nicked and causing a short circuit. 

7.

 Extra cable can cause signal loss and act as an “antenna” for noise.  Use

only high-quality RCA cables that are no longer than necessary to make a

direct connection with the source unit and amplifiers.

WIRING PRECAUTIONS

6

www.quantumaudio.net

Summary of Contents for QA3X

















Reviews: