background image

 

1

 

THANK YOU 

 

 

Thank you for your purchase of the Quantun two-way Mobile radio. 

This easy-to-use radio adopts the latest advanced technology, 

providing reliable communication performance in today’s demanding 

communications environment. 

 

Before operating this radio, please read this manual carefully to be 

acquainted with its operation and features.   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

z

 

Do not touch the metal surface of the radio while it is in use. 

z

 

Do not mount the radio such that the chassis can come in contact with skin.   

z

 

High temperature may burn your skin.   

 

 

                            Caution:  Changes or modifications not expressly approved by the party responsible                                

                                                            for compliance could void the user's authority to operate the equipment.                               

                                                                            This device complies with part 15 of the FCC Rules.                               

                                                                                             Operation is subject to the condition that this device does not cause harmful interference.

 

 

 

 

Summary of Contents for QM-790-V



























Reviews: