background image

Quark-elec Manual

https://www.quark-elec.com

13 of 14

2018

V2.0

11. Troubleshooting

Phenomenon

Trouble Part

Reason

Solution

RXA indicator falls

AIS channel

NMEA 0183 port

disconnection

Reconnect cable

RXB indicator falls

AIS channel

NMEA 0183 port

disconnection

Reconnect cable

GPS indicator falls

GPS

antenna

Disconnection or

loose

Check the connection

TX indicator falls

Serial port

Serial definition fault

or disconnection

Check configuration tool to

check report rate

VCC indicator falls

Power cable

Cable disconnection

Check if the connection is

correct

VCC indicator

flashes

Power cable

Power supply is out

of defined range

Set or transfer power level

within defined range

12. Limited Warranty and Notices

Quark-elec warrants this product to be free from defects in materials and manufacture for one year

from the date of purchase. Quark-elec will, at its sole option, repair or replace any components that

fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts

and labour. The customer is, however, responsible for any transportation costs incurred in returning

the unit to Quark-Elec. This warranty does not cover failures due to abuse, misuse, accident or

unauthorized alteration or repairs. A returns number must be given before any unit is sent back for

repair.

The above does not affect the statutory rights of the consumer.

Disclaimer

This product is designed to aid navigation and should be used to augment normal navigational

procedures and practices. It is the user’s responsibility to use this product prudently. Neither Quark-,

nor their distributors or dealers accept responsibility or liability either to the products user or their

estate for any accident, loss, injury or damage whatsoever arising out of the use or of liability to use

this product.

Quark- products may be upgraded from time to time and future versions may therefore not correspond

exactly with this manual. The manufacturer of this product disclaims any liability for consequences

arising from omissions or inaccuracies in this manual and any other documentation provided with this

product.

Document history

Issue Date

Changes / Comments

1.0

27-04-2018

Initial release

2.0

24-10-2018

New 2018 format

Summary of Contents for QK-A042T















Reviews: