background image

Product Manual

9605

Pushbutton Station

for Allen-Bradley SLC500 Programmable Controller

DH+ Interface

Quartech Corporation

159

2

3 Angelo Drive

Macomb Township, Michigan 48042-4050

Phone:  (

5

8

6

) 781-0373   FAX: (

5

8

6

) 781-0378

   www.

Q

uartech

C

orp.com

PM9605 Revision 1

The product described in this document can have a variety of uses, the user and those responsible for applying this
equipment must satisfy themselves as to the acceptability of each application and the use of the unit.  Under no
circumstances will QUARTECH CORPORATION be responsible or liable for any damage, including indirect or
consequential losses resulting from the use, misuse, or application of the unit.

The text, illustrations, charts, and examples included in this document are intended solely to help explain applications
of the product.  Due to the many variables associated with specific uses or applications, QUARTECH CORPORATION
cannot assume responsibility or liability for actual use based upon the data provided in this document.

No patent liability is assumed by QUARTECH CORPORATION with respect to the use of circuits, information,
equipment, or software described in this document.

This document is subject to change without notice.

Summary of Contents for 9605



















Reviews: