QUATRO
Air Technologies Inc.
Engineers Of Clean Air
30 Hymus Blvd., Pte-Claire, Quebec, Canada H9R 1C9 Tel.: (514) 630-4444 Fax: (514) 630-4454 info@quatroair.com
2
Stage II (Top)
HEPA (p/n F075)
- Under typical applications, should last between 12 to 24 months (depending on applications);
- Switch OFF the unit . Unplug from wall outlet. Unlatch the top section and remove; - Remove HEPA Filter from the top
ALTERNATE Stage II FILTER SEQUENCE (Top)
HEPA (p/n F074/F074)
- Switch OFF the unit . Unplug from wall outlet. Unlatch the top section and remove;
- Remove
2 HEPA Filters
and replace with
(2) NEW F074 FILTERS
(MUST BE COMPRESSED BY METAL COMPRESSION ANGLE ASSEMBLY)
SPEED CONTROL
The unit is equipment with built-in speed control. By pressing & holding down the speed UP or DOWN triangles, you respectively increase and
decrease unit’s speed. When you reach the highest or lowest speed, the panel will continuously BEEP alerting you that you have reached the
highest or lowest speed.
MOTOR SERVICE
WARNING: Switch unit off and unplug power cord from wall before servicing the blower.
Motor contains double shielded ball bearings with a special lubricant, assuring long life and quiet operation. No extra motor maintenance is required.
ANNUAL GENERAL INSPECTION
The sealing integrity of the unit is essential. Every 12 months, verify that all gaskets are in proper condition. Should the door gaskets adhere to the unit
when opening a door, lubricate its surface with a transparent grease or petroleum jelly. Should the unit be relocated continuously for optimum efficiency,
ensure all casters are tightly fastened.
Resetting “Service Filter(s)” Alert
Control panel contains a pre-set 2000 operating hour countdown timer to remind you to check filter status. When timed out:
1- Ensure filter access door is closed, 2- Plug power back to the unit
3- Press & hold SPEED UP & DN simultaneously until unit BEEPS 4- Hold for 10+ seconds, when panel is beeping continuously, release buttons
5- You are now in RESET MENU, in this condition, “System ON” Led is FLASHING QUICKLY
6- Press SPEED DN (2 Times) until
“Service Filter(s)”
LED is FLASHING
7- Press & HOLD POWER button while
“Service Filter(s)”
LED is FLASHING & unit is BEEPING continuously
8- Release, when LED stops FLASHING & stops BEEPING
TROUBLESHOOTING GUIDE
Symptoms
Possible Cause
Suggested Solution
Unit will not start
Faulty Power supply
Return or supply grille blocked
HEPA filter improperly installed
Blown fuse
Unit not plugged into receptacle
Check breaker box
Remove obstruction
See Section 9, 10,11
Replace fuse
Plug unit in
Excessive noise
Motor wheel contacting inlet ring
Fan isolators loose or off
Realign/replace motor
Replace isolator
Insufficient airflow
Obstruction in system or clogged filters
Remove obstruction or replace filters
Excessive airflow
Filters not in place
Install filters
REDUCTION IN AIRFLOW
As the unit cleans the air, the filters are removing the particles of dust and dirt in the air. As the filters accumulate dirt (both visible and microscopic), a restriction on
the motor is created. As the restriction becomes greater, the air capacity delivered by the motor decreases and the air purification less effective. IT IS VERY
IMPORTANT TO CHANGE FILTERS ON A REGULAR BASIS (See filter maintenance above).
WARRANTY
QUATRO Air Technologies warrants its equipment to be free from defect in material and workmanship under normal use and service for a period of two year
from date of shipment. QUATRO's obligation under this warranty shall be limited to replacing any parts, thereof, which shall be demonstrated to have been
defective. This is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness.
QUATRO claims no warranty as to merchantability or as to the fitness of the merchandise for any particular use and shall not be liable for any loss or damage.
No person, firm or corporation is authorised to assume for QUATRO any other liability in connection with the sale of these goods. Equipment, parts and
material manufactured by others and incorporated in QUATRO's equipment are warranted by QUATRO only to the extent of the original manufacturer's liability
to QUATRO Air Technologies Inc.
Conditions and Limitations:
This warranty does not cover
abuse, misuse, maintenance negligence, improper assembly, acts of vandalism, acts of God, fear
wear, modifications of the equipment or installation of a part not recommended by QUATRO Air Technologies, as well as operation of the equipment at
voltages other than those specified by QUATRO Air Technologies Inc.
REPLACEMENTS
Description
Part No:
Description
Part No:
Description
Part No:
Dust Filter (6/bx)
F071-BX
Caster Kit (4/pak)
AR188
Replacement Plastic grille
H507
HEPA Filter, 6” Deep
F075
Caster Kit (1/pak)
AR120
HEPA Filter, 2” Deep
F074 (2 reqd)