background image

GV320 User manual

                                                            

 

TRACGV320UM001                                                               

- 16 - 

Active 

5.0V to 32V 

Inactive 

0V to 3V or Open 

 

Figure 10. 

Typical Ignition Detection 

IGN (Pin3)is used for ignition detection. It is strongly recommended to connect this pin to 
ignition key “RUN” position as shown up. 
An alternative to connecting to the ignition switch is to find a non permanent power source 
that is only available when the vehicle is running. For example the power source for the 
FM radio. 
IGN signal can be configured to start transmitting information  to  backend  server when 
ignition is on; and enter power saving mode when ignition is off. 

There are three general purpose digital inputs on GV320. They are all negative trigger. 

Table 8.

 

Electrical Characteristics of the digital inputs 

Logical State 

Electrical Characteristics 

Active 

0V to 0.8V 

Inactive 

Open 

 
The following diagram shows the recommended connection of a digital input. 

3.9.

 

Digital Inputs 

  Queclink 

Confidential

Summary of Contents for GV320






















Reviews: