background image

GV75W User Manual

 

 

 

TRACGV75WUM001                             

                                                                                                    ‐ 11 ‐ 

Figure 2: Typical Power Connection

 

 

 

3.4.

 

Ignition Detection 

Table 6: Electrical Characteristics of Ignition Detection

 

 

 

Figure 3: Typical Ignition Detection

 

 

The  white  wire  is  used  for  ignition  detection.  It  is  strongly  recommended  to  connect  this  wire  to 
ignition key at “RUN” position as shown above. 
An alternative to connecting to the ignition switch is to find a non‐permanent power source (like the 
power source for FM radio) that is only available when the vehicle is running. Ignition signal can be 
configured to start transmitting information to the backend server when ignition is on and to enter 
power saving mode when ignition is off. 
 
 

3.5.

 

Digital Input 

There is a negative trigger input on GV75W. For negative trigger input, the electrical conditions are 
as follows: 

Logical State 

Electrical State 

Active 

0V to 0.8V 

Inactive 

1.7V to 32V or Open 

Table 7: Electrical Conditions of Negative Trigger Inputs 

 
The connection is shown as follows: 

 

Figure 4: Connection for Negative Trigger Inputs 

Logical Status 

Electrical Status 

Active 

5.0V to 32V 

Inactive 

0V to 3V or open 

Summary of Contents for GV75W


















Reviews: