background image

- 2 - 

Foreword 

This  manual  applies  to 

L-RF-EDFA

  series 

1550nm

  EDFA.  It  mainly  describes 

the  performance  characteristics,  technical  parameters,  installation  and  debugging, 

common troubleshooting, and other related content of the product. In order to ensure 

that the equipment can be successfully installed and safely operated, please read this 

manual carefully before installing and debugging the equipment. And the installation 

and  debugging  should  be  strictly  according  to  the  specified  steps  on  the  manual  to 

avoid  unnecessary  damage  to  equipment  or  accident  harm  to  the  operator.  Any 

questions, please contact with us in time. 

Special Tips:

 

1

Er-doped Fiber Amplifier is high end professional equipment, and its installation 

and debugging must be operated by special technician. Read this manual carefully 

before  operating  to  avoid  damage  to  equipment  caused  by  fault  operation  or 

accident harm to the operator. 

2

While  the  fiber  amplifier  is  working,  there  is  an  invisible  laser  beam  from  the 

optical  output  adapter  on  the  front  panel.  Avoiding  permanent  harm  to  the  body 

and eye, the optical output should not aim at the human body and human should 

not look directly at the optical output with the naked eye!

   

3

Please make sure that the ground terminal of the case and power outlet has been 

reliably grounding before turning on the power (Grounding resistance should be < 

4Ω)  to  prevent  the  static  damage  the  pump  laser  device  and  harm  to  human 

because of case charged.   

4

To ensure the equipment can work stable over a long time in voltage unsteady or 

poor voltage wave region, it´

s recommend to the customer that he equips special 

AC regulated power supply, or even AC uninterrupted power supply (UPS) system 

for conditional regions. In the region with large temperature variation environment 

(The  equipment's  ideal  work  environment  temperature  is  25°C)  or  bad  room 

environment  it´

s  recommend to  the  customer that  he  equips special air-condition 

www.questtel.com

sales@questtel.com

EDFA Optical Amplifier

 User Manual

 

L-RF-EDFA-14dBm

Summary of Contents for L-RF-EDFA-14dBm

















Reviews: