background image

8

INSTALLATION AND USE MANUAL 

QNN 

- REV000A

EN

4 - Safety

4.0 - Precautions

• Comply with all the safety warnings included in this manual.

• Comply with all the technical parameters indicated in this manual.

• Handle with care paying attention to avoid damaging the gyro or getting injured.

• Strictly observe all the local accident prevention standards during both assembling and regular operation.
• Maximum cleanliness must be guaranteed during operations.

BEFORE USING THE GATEWAY QNN CAREFULLY READ THIS USER’S MANUAL. IF IN DOUBT, IMMEDIATELY 
CONTACT YOUR NEAREST AUTHORISED QUICK® DEALER.

4.1 - Warnings

• The QNN operates within 90÷32 Vac power supply

Connect to the electrical line in compliance with the protection standards in force.

• 

During navigation, we recommend not disconnecting the power supply to prevent damages to 

the connected products.

• DO NOT open the device case.

• DO NOT introduce foreign objects inside the protection cover.

• 

Before performing any operation, such as 

cleaning or a update software,

 in order to prevent any 

damage to people or objects caused by an accidental start-up. Disconnect the 

Gateway QNN from the 

power supply.

• Restore the power supply only after having correctly installed all the safety devices that were removed to 

carry out the operations.

CLEANING THE APPLIANCE

• DO NOT USE 

solvents or fuels to clean the appliance.

• DO NOT REMOVE 

the safety labels on the equipment.

4.2 - Environmental requirements

We recommend positioning the stabilizer in a dry, ventilated place in order to enable it to operate at full power and

be protected from atmospheric agents.

Make sure that the installation location is suitable for correct installation and easy inspection.

Do not use this product as a primary navigation instrument. The operator is responsible for the use 

of the accessories on the QNN and prudent methods for safe navigation.

 The software contained in 

the QNN could change without notice or may not be updated. The alarms refer to the use of the individual 

connected accessories and to the use of the QNN

You are aware and accept to be the only persons responsible for use of the QNN and all decisions taken as 

a result. In using this service, you free Quick SpA and waive presenting any claims in relation to this service.

The QNN does not replace standard navigation practices and must not be used as single sources of 

reference. The QNN is only a navigation aid and must be used along with approved methods for safe 

navigation. The captain of the ship is always responsible for the course correction.

All navigation aids are subject to inaccuracies and discrepancies that, if not taken into consideration, can 

cause accidents and problems and, consequently, the loss of life or serious injuries.

F

Summary of Contents for QNN





























Reviews: