background image

3

GB-031AB/f.

Safety instructions

1.  Read and strictly follow the installation and operating instructions to ensure a 

long life and reliable boiler operation. 

2.  An efficient electrical installation which has been completed in accordance with 

the binding norms of electric installation.

3.  A wet central heating system equipped with appropriate expansion vessel made 

according to binding norms of hydraulic installation.

4.  A wet central heating system must be flushed before boiler installation.

5.  Do not install any barrier fittings (e.g. valves) on the outlet of the safety valve.

6.  Boiler must be installed on an even wall surface. 

7.  Boiler must not be installed in a humid place or in a place exposed to the danger 

of explosion.

8.  Boiler installation and all electrical and hydraulic work must be performed by a 

qualified professional installer.

9.  All installation work must be performed when the power and water supply is 

turned off.

10.  EKCO.LN2 and EKCO.LN2...p model is equipped with a differential pressure 

relief valve (bypass). It allows the system to keep minimal flow of heating medium 

through the boiler and reduce noises in installation during the thermostatic valves 

closing.

11.  Electric installation should be equipped with residual current protective devices 

and other solutions which will ensure disconnecting the heater from the source 

of power (intervals between all their poles should not be less than 3 mm).

12.  Boiler is pre-set by the manufacturer to work with the central heating system. 

Change the factory settings („Extended Menu”) to boiler work with DHW Cylinder.

13.  Do not drain the water from central heating system after the heating season.

14.  Leave the controller in stand-by mode and do not cut off power supply between 

the heating seasons.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities or lack of experience and knowledge, unless they have been given supervision or 

instruction concerning use of the appliance by a person responsible for their safety. 

Children should be supervised to ensure that they do not play with the appliance.

Summary of Contents for EKCO.LN2

















Reviews: