background image

51

2. SETUP INSTRUCTIONS

 

 

IMPORTANT:

 Prior and during assembly, inspect all components including fabric, frames, connecting    

 

 

points, plastic tubing, etc. Look for tears, cuts, punctures or anything which may yield inaccurate  

 

 

 

results or may cause injury to operator. 

2.1 

Fan Base Stand

NOTE: It is always best to setup base stand near the grill of fan to be tested

1.  Lay the bottom square frame flat 

a.  Attach each (4) of the 1” square tube legs using the button pins

b.  Insert ¾” square tube leg into the 1” leg and adjust to height needed using 

button pins

i. 

Top of frame needs to be between 4’-5’ from ceiling

ii.  It is recommended to adjust height of legs prior to adding top octagonal 

frame

c. 

FOR RETROTEC FANS:

 

i. 

Slide Retrotec fan in between the 4 legs (See pictures below)

ii.  Place fan strap carabiners into hooks on top octagonal frame (See pictures below)

iii.  Insert octagonal frame pegs into the 4 rectangular legs (See pictures below)

iv.  Work the fan strap around the Retrotec fan, buckle it together and pull tightly (See pictures below)

 

d.  

FOR TEC MODEL 3 FANS:

 Add top octagonal frame by sliding the pegs into the 4 legs. Lay down and  

 

    install blower door fan into stand by attaching carabiners to hooks (see picutres below)

2. 

Pick stand back up carefully and slide stand off to the side to make room for setting up the flow hood

Summary of Contents for WHF-PFH













Reviews: