background image

13

41451-01

Programming

NOTES:

• The clock flashes when the time has not been set.

• At any time while you are setting the Day/Time, you can press the PROGRAM key to

toggle between AM/PM format and military time format.

• To quickly exit the Day/Time setting mode, you can press the DISPLAY key or wait 15

seconds without pressing any keys.

• The time displayed will be frozen in Day/Time setting mode; however, the internal clock

is still running. If no value is changed, then the frozen time will be replaced by the
internal clock when you exit the Day/Time setting mode.

• If the power is lost to the unit, the memory will maintain the clock for at

least 12 hours.

Pre-set Programming

As discussed in the Manual and Auto Operating Modes section of the manual (pg. 9), your
air purifier comes with pre-set programs. For your reference, these programs are listed again
below. When you turn your air purifier to Auto Mode, these programs are active unless you
override them with your personalized programs. Refer to the next section, User Program-
ming, to learn how to input your own programs.

Table 3: Pre-set programming provided for each air purifier.

Program

Setpoint Time

Blower  Speed

1

8:00 am

2 (Medium)

2

3:00 pm

3 (High)

3

5:00 pm

2 (Medium)

4

10:00 pm

1 (Low)

41451-01_Rev 8-6-04.pmd

8/5/04, 5:05 PM

13

Summary of Contents for 30401

























Reviews: