background image

 

QVM 9

 

Series

 

6

 

 

 

 

 

 

 

 

Hot  water  temperatures  required  for  automatic  dishwasher  and  laundry  use  can  cause  scalds  and 

burns resulting in serious personal injury and/or death. 

The temperature at which injury occurs varies with the person's age and time of exposure. 

The  slower  response  time  of  disabled  persons  increases  the  hazards  to  them.  Never  allow  small 

children to use a hot water tap, or to draw their own bath water. Never leave a child or disabled person 
unattended in a bathtub or shower. 

The water heater should be located in an area where the general public does not have access to the 

temperature control. 

Lower water temperatures should be used to avoid the risk of scalding. It is further recommended, in 

all  cases,  that  the  water  temperature  be  set  for  the  lowest  temperature  which  satisfies  the  user's  hot 
water needs. This will also provide the most energy efficient operation of the water heater and minimize 
scale formation in the heat exchanger, thus prolonging the life of the unit. 

Setting  the  water  heater  temperature  at  120°F  will  reduce  the  risk  of  scalds.  Some  states  require 

settings  at  specific  lower  temperatures.  The  table  below  shows  the  approximate  time-to-burn 
relationship for normal adult skin. 

 

Table- Risk of Scalds 

 

Temperature 

Setting 

Time to Produce 2nd 3rd 

Degree Burns on Adult Skin 

Over 170  ℉ 

Nearly instantaneous 

160  ℉ 

About 1/2 second 

150  ℉ 

About 1-

1/2

 second 

140  ℉ 

Less than 5 seconds 

130  ℉ 

About 30 seconds 

120  ℉  of less 

More than 5 minutes 

 

USE ANTI-SCALD VALVE(S)

  IN  HOT  WATER  SYSTEM  TO  REDUCE  THE  RISKS  OF  SCALDING  AT 

POINTS OF USE SUCH AS LAVATORIES, SINKS AND BATHING FACILITIES. 
 

Scalds 

 First Aid

 

1.  Remove clothing;

   

Remove all wet clothing, quickly. Wet clothing retains the heat.

 

2. Apply cold water for 30 minutes;

 

Immediately  submerge  the  burnt  area  in  cold  water  for  30 

minutes to reduce the heat in the skin, preventing deeper burning. Never use butter, oils or ointment 
to cover the burn. They may retain the heat.

 

3. Keep the scalded person warm;

 

Place a blanket around the person.

 

4. Seek medical advice;

 

Call your medical advice hotline and describe the scald, follow their directions. 

Safety Issues

 

Summary of Contents for QVM9 Series













































Reviews: