background image

ENGLISH 

 

Cod. 2200780113  01 -  Edition 10/2014 - 1 

 
 
 

 

 

 

 

INSTRUCTION AND MAINTENANCE MANUAL 

 

DRYERS 

 

QPNC 10  to  QPNC 50

 

 
 

 

 

 

 

 
 

 

 

 

 
 

 

 

 

 

 
 

CONTENTS

 

 

PART A: INFORMATION FOR THE USER 

11.0   UNPACKING

 

1.0  GENERAL CHARACTERISTICS

 

12.0   INSTALLATION

 

2.0   INTENDED USE

 

13.0   DIMENSIONS AND TECHNICAL DATA

 

3.0  OPERATION

 

14.0   MACHINE ILLUSTRATION

 

4.0  GENERAL SAFETY STANDARDS

 

15.0   PARTIAL ROUTINE MAINTENANCE

 

5.0  DESCRIPTION OF DANGER SIGNALS

 

16.0   SCRAPPING THE DRYERS

 

6.0  DANGER ZONES

 

17.0   TROUBLE-SHOOTING AND EMERGENCY REMEDIES

 

7.0  SAFETY DEVICES

 

PART B: INFORMATION RESERVED FOR TECHNICALLY SKILLED 
PERSONNEL 

8.0  POSITION OF PLATES

 

18.0  STARTING UP

 

9.0  DRYERS ROOM

 

 

10.0 TRANSPORT AND HANDLING

 

 

 

ATTENTION: THERE IS A COPY OF THE WIRING DIAGRAM INSIDE THE ELECTRIC PANEL 

 

ADDRESSES OF ASSISTANCE CENTRES 

 

In the event of breakdown or malfunction of the dryer, switch it off and do not tamper with it. If repairs are needed, apply only to a technical 

assistance centre approved by the manufacturer and insist on the use of original spare parts. Failure to comply with the above may 
endanger the safety of the machine. 
 

INTRODUCTION 
Keep this manual with care for future consultation; the use and maintenance manual is an integral part on  the dryer.  Read this 
manual carefully before carrying out any operations on the dryer. 

The installation of the dryer and all operations involving it must be performed in conformity with the regulations in force 
concerning electric plants and personal safety.

 

 

Code 

2200780113 

01 

 

Edit. 10/2014 

 

 

 

 

 

READ THIS MANUAL CAREFULLY BEFORE CARRYING OUT ANY OPERATIONS ON THE DRYER. 

 

 

Summary of Contents for QPNC 10













Reviews: