background image

ISO

  

|

  17

UL507 WARNING STATEMENT
Section 64 – General

READ AND SAVE THESE INSTRUCTIONS

1 Prevent a risk of fire, electric shock, or injury to persons, 

by cleaning and user maintenance, such as lubrication.

2 Unplug or disconnect the appliance from the power supply 

before servicing.

3  WARNING To Reduce The Risk Of Fire Or Electric  

Shock, Do Not Use This Fan With Any Solid State Speed 
Control Device.

4 WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC 

SHOCK, OR INJURY TO PERSONS, OBSERVE THE 
FOLLOWING:

 a) Use this unit only in the manner intended by the 

manufacturer. If you have questions, contact the 
manufacturer.

 b) Before servicing or cleaning unit, switch power off at 

service panel and lock the service disconnecting means to 
prevent power from being switched on accidentally. When 
the service disconnecting means cannot be locked, securely 
fasten a prominent warning device, such as a tag, to the 
service panel.

5 CAUTION – For General Ventilating Use Only. Do Not Use 

To Exhaust Hazardous Or Explosive Materials And Vapors.

 

Additional safety information is included in the instruction 
manual on page 6.

UL507 WARNING STATEMENT
Section 64A – Installation Instructions

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, 
OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

  a) Installation work and electrical wiring must be done by 

qualified person(s) in accordance with all applicable codes  
and standards, including fire rated construction.

  b) Sufficient air is needed for proper combustion and 

exhausting of gases through the flue (chimney) of fuel burning 
equipment to prevent back drafting. Follow the heating 
equipment manufacturer’s guideline and safety standards 
such as those published by the National Fire Protection 
Association (NFPA), and the American Society for Heating, 
Refrigeration and Air Conditioning Engineers (ASHRAE),  
and the local code authorities.

  c) When cutting or drilling into wall or ceiling, do not damage 

electrical wiring and other hidden utilities.

  d) Ducted fans must always be vented to the outdoors.

  e) If this unit is to be installed over a tub or shower, it must be 

marked as appropriate for the application and be connected 
to a GFCI (Ground Fault Circuit Interrupter) – protected 
branch circuit.

Additional installation instructions are included in the instruction 
manual on pages 8–11.

UL507 WARNING STATEMENT
Section 64B – User Servicing Instructions

All user servicing instructions are included in the instruction 
manual on pages 12–13.

Summary of Contents for ISO



















Reviews: