Qvis 72-8P Series User Manual Download

Page: 127 / 233

118

4.12.4 RAID Manager

Important:

Please make sure your purchased product support the RAID function, otherwise you

cannot see the following interface.

This is for you to manage RAID HDD. It can display the RAID name, type, free space, total space,

status , etc. Here you can add/delete RAID HDD.

Click Add button to select RAID type and then select HDDs, click OK button to add. See Figure

4-118

Click Hot spare disks tab name, you can add the hot spare HDD. See Figure 4-119. Select a hot

spare device and then click Delete button. Click Apply button to delete.

Figure 4-118

Summary of Contents for 72-8P Series










































































































































































































































Search results

Summary of Contents for 72-8P Series

Reviews:

Related manuals for 72-8P Series

Brands by name

Popular brands

Qvis 72-8P Series, User Manual

Search results

Summary of Contents for 72-8P Series

Reviews:

Related manuals for 72-8P Series

Brands by name

Popular brands