background image

 

 

 

Version 24.07.2018 

CAM(V97)/(V30) 

RL3-MIB92 

P

a

g

e

6

 

 
1.4.1.1.

 

Enabling the interface’s video inputs (dip 2-3) 
 

Only by dip switches enabled video inputs can be accessed by switching through the 
interface’s video sources. It is recommended to enable only the required inputs. Disabled 
inputs will be skipped while switching through the video interfaces inputs. 

 

1.4.1.2.

 

Rear-view camera setting (dip 5) 

 

If set to OFF, the interface switches to factory picture while the reverse gear is engaged to 
display factory rear-view camera or factory optical park system picture. 
If set to ON, the interface switches to its rear-view camera input while the reverse gear is 
engaged. 

 
1.4.1.3.

 

Monitor selection (Dip 6-8) 

 

Dips 6-8 customize the monitor-specific video settings. 
 

Note:

 Dip 4 is out of function and has to be set to 

OFF

 
 
1.5.

 

Settings of the 4 Dip switches (CAN functions – red) 

 
 
Dip position down is ON and position up is OFF.

 

 

 
 

Vehicle/Navigation 

Dip 1 

Dip 2 

Dip 3 

Dip 4 

All vehicles 

OFF 

ON

 

OFF 

OFF 

 

After each Dip-switch-change a power-reset of the Can-box has to be performed!  

 
 

2.

 

Installation 

 

To install the interface, first switch off the ignition and disconnect the vehicle’s battery. 
Please read the owner`s manual of the car, regarding the battery`s disconnection! If 
required, enable the car`s Sleep-mode (hibernation mode)  
In case the sleep-mode does not succeed, the disconnection of the battery can be done 
with a resistor lead. 
If the necessary stabilized power supply for the interface is not taken directly from the 
battery, the chosen connection has to be checked for being constantly stabile.  
The interface needs a permanent 12V source!

 

 
 

2.1.

 

Place of installation 

 
The interface is supposed to be installed at a suitable location behind the vehicle`s head-
unit.   

 

Summary of Contents for RL3-MIB92




















Reviews: