INSTRUCTIONS
FIELD-ADJUSTABLE
X34®
INSTALLATION
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com
0-10V DIMMABLE WIRING
CLEANING & MAINTENANCE
Universal voltage driver permits operation at 120V through 277V,
50 or 60Hz. Units ordered with /480V suffi x are 480V only, 50 or 60Hz.
For 0-10V dimming, follow the wiring instructions as shown in Fig. 5.
1. Connect the black fi xture lead to the
LINE
supply lead.
2. Connect the white fi xture lead to the
COMMON
supply lead.
3. Connect the
GROUND
wire from fi xture to supply ground.
Do NOT connect the
GROUND
of the dimming fi xture to
the output.
4. Connect the purple fi xture lead to the DIM V+ lead.
5. Connect the pink fi xture lead to the DIM V- lead.
6. Cap the yellow fi xture lead, if present. Do NOT connect.
CAUTION: Be sure fi xture temperature is cool enough to touch.
Do not clean or maintain while fi xture is energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. Do not open the fi xture to clean the LED. Do not touch the LED.
PINK
LIGHT
FIXTURE
Vaux 12V
YELLOW
GROUND
GROUND
( - ) DIM V
( + ) DIM V
COMMON
LINE
BLACK
WHITE
PURPLE
Fig: 5
X34 HO - IN - 0322
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
Answered promptly - sales@rablighting.com
Free Lighting Layouts
Answered online or by request
© 2022 RAB LIGHTING Inc.
RAB WARRANTY:
RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty
Note:
These instructions do not cover all details or variations in equipment nor do they
provide for every possible situation during installation, operation or maintenance.
P-100120
Photocell Operation:
This product is equipped with a photocell.
Photocell factory
setting is set to the “OFF” position
. Should you wish to enable the
Photocell “On” feature slide the center switch to the “ON” position
(Fig 4)
.
If the Photocell is set to the “ON” position and it is daylight, it
may take up to 60-seconds for the light to turn off .
Color Temperature
(CCT)
Selection:
This product is equipped with 5000K, 4000K or 3000K CCT color
temperature selection. For maximum light output use the 4000K
color temperature.
Power
(%)
Selection:
This product is equipped with 50%, 75% and 100% power output
selection.
Follow instructions below to change Photocell operation, Color
Temperature
(CCT)
and/or Power
(%)
from factory settings.
Factory Settings:
100% Power, 4000K CCT, Photocell Off
1. Locate the selector switches on side of housing as shown in
Fig. 3.
2. Select
Color Temperature
(CCT)
,
Power
(%)
and/or
Photocell
on/off function by sliding the respective switch to the desired
value
(Fig. 4)
.
FIELD ADJUSTMENT
Fig: 3
Selector Switches
100 75 50
5k 4k 3k
Fig: 4
Color Temperature
(CCT)
Power
(%)
Photocell
(on/off )
Note: For external dimming control set power switch to 100% and
turn off Photocell switch.
TROUBLESHOOTING
1.
Check that the line voltage at the fi xture is correct. Refer to
wiring directions.
2.
Is the fi xture grounded properly?
3.
Is the photocell, if used, functioning properly?
