background image

9

09.2009

General safety instructions

•  Check implement and tractor for road safety and operational safety before each use!
•  As well as the instructions in this operating manual, also observe the generally applicable safety 

and accident prevention regulations!

•  The installed warning and information signs give important information for safe operation – 

 compliance with these provides your safety!

•  Attach and check transport equipment (lighting, warning devices)!
•  The corresponding regulations must be observed when using public roads!
•  Check the immediate vicinity (children) before starting, before swivelling the implement in and out 

and before operation!

•  Riding on the implement during the work and the transport journey is not permitted!
•  It is not permitted to stand in the swivelling and working area of the implement!
•  The implement must be coupled in accordance with the instructions and only attached to the 

intended equipment!

•  Particular caution is required when coupling and uncoupling the implement to or from the tractor!
•  Do not step between the implement and the tractor/packer!
•  Permitted axle loads, overall weights and transport dimensions must be complied with!

•  Driving behaviour, steering and braking ability are influenced by attached heavy work implements! 

 

Therefore, sufficient steering and braking ability must be ensured; use ballast weights if 

 necessary!

•  The inertia and centre of gravity of the implement must be taken into account when negotiating 

bends; there is a danger of tipping!

•  Ensure stability during coupling and uncoupling; take precautions against rolling away on  

sloping terrain!

•  Only perform the swivelling process if there are no persons in the danger zone!

•  Spare parts must comply with at least the technical requirements specified by the implement 

manufacturer!  

This is always the case for original spare parts!

Appropriate use

The NE packer trailed implement is exclusively intended for usual agricultural use for soil cultivation. 

Any other use is considered to be improper. The manufacturer is not liable for any damage arising 

from improper use. The risk for this is borne solely by the user.

Proper use also includes compliance with the operating, maintenance and repair instructions speci-

fied by the manufacturer.

Ensure that all relevant accident-prevention regulations are observed, as well as generally accepted 

safety procedures, health and safety regulations and road traffic legislation.

The Nockering Roller NE must only be used, maintained and repaired by persons who are familiar 

with it and who have been instructed about the dangers.

Unauthorised modifications to the implement exclude any liability of the manufacturer for damage 

resulting from this.

Subject to technical modifications

Summary of Contents for Packer CR

















Reviews: