background image

THE WARRANTY DOES NOT COVER:

• Start-up and setting up of the product.
• Damage resulting from normal wear and tear of the product.
• Damage resulting from improper use of the product.
• Damage resulting from assembly or start-up not in accordance with the user manual.
• Breakdowns related to carburetion beyond 90 days and fouling of carburetors.
• Periodic and standard maintenance events.
• 

Actions of modification and dismantling that directly void the warranty.

• 

Products  whose  original  authentication  marking  (brand,  serial  number)  has  been  degraded,  altered  or 

withdrawn.

• Replacement of consumables.
• The use of non-original parts.
• Breakage of parts following impacts or projections.
• Accessories breakdowns.
• 

Defects and their consequences linked to any external cause.

• 

Loss of components and loss due to insufficient screwing.

• Cutting components and any damage related to the loosening of parts.
• Overload or overheating.
• Poor power supply quality: faulty voltage, voltage error, etc.
• Damages resulting from the deprivation of enjoyment of the product during the time necessary for repairs 

and more generally the costs related to the immobilization of the product.

• The costs of a second opinion established by a third party following an estimate by a SWAP-Europe repair 

station

• The use of a product which would show a defect or a breakage which was not the subject of an immediate 

report and/or repair with the services of SWAP-Europe.

• Deterioration linked to transport and storage

*

.

• Launchers beyond 90 days.
• Oil, petrol, grease.
• Damages related to the use of non-compliant fuels or lubricants.

In accordance with transport legislation, damage related to transport must be declared to carriers within 48 

hours maximum after observation by registered letter with acknowledgement of receipt.
This document is a supplement to your notice, a non-exhaustive list.

Attention:

 all orders must be checked in the presence of the delivery person. In case of refusal by the 

delivery person, it you must simply refuse the delivery and notify your refusal.

Reminder:

 the reserves do not exclude the notification by registered letter with acknowledgement within 72 

hours.

Information: 

Thermal devices must be wintered each season (service available on the SWAP-Europe site). Batteries must 

be charged before being stored.

WARRANTY EXCLUSIONS

21

Summary of Contents for RAC196PTIL8T-1























Reviews: