background image

14 

6.  MAINTENANCE AND STORAGE 

 
Before working on the cutting system of the machine, switch off the engine and remove the spark 
plug’s cap. 
 
a.  Cleaning the mower 

-  Cut grass is damp. Regular cleaning after each use will ensure better functioning of the mower and 

reduce the risk of corrosion or seizure. 

-  Having finished mowing, allow the engine to cool then remove accumulated grass clippings from and 

around the engine with a brush. 

-  Clean the grass collection bag annually with a brush or gentle spray of water. 
-  Disconnect the spark plug’s cap and tilt the mower on its side with the air filter and carburettor 

uppermost. 

-  Remove any remaining cut grass from the cutting system with a scraper and a brush. 
-  Reposition the mower onto its four wheels. 
-  Do not use a pressure washer or hot water to clean the mower. Be careful to avoid soaking parts such 

as the engine, air cleaner, wheel bearings and metal fastenings. Dry off the machine before storing 
by leaving it running for a few minutes on a flat, clear surface to prevent corrosion or seizure. 

 
b. Blade 

maintenance 

WARNING: Wear gloves, turn off the engine and remove the spark plug before proceeding. 
 

 

 

The blade is made of hardened steel. To get a clean job, sharpen the blade frequently, about every 25 
hours of use. Make sure the blade is always well balanced. 
Insert a small iron pin (2 or 3 mm in diameter) into the hole in the middle of the blade: it must remain 
horizontal. If the blade does not stay horizontal, balance it by sharpening it further on the side where it is 
leaning. 
WARNING: Use only original spare parts. Poor quality replacement parts can cause serious damage to 
your mower and affect your safety. 

 

  

1

 

 

To remove the blade, loosen the screw, check the blade bracket, and replace all parts if they are worn or 
damaged. 
When reassembling the blade, make sure that the cutting edges are in the same direction as the direction 
of rotation of the motor. The tightening torque of the blade screw should be 3.7 kg * m / s 2 (37 Nm) and 
can be checked with a torque wrench. 

 
c. Storing 

the 

mower 

Store your mower in a dry, well

-

ventilated area, away from flames, sparks or heat sources. If the storage 

area is accessible to children, immobilise the machine by disconnecting the spark plug’s cap. Storing the 

Summary of Contents for RAC5175SPM





















Reviews: