background image

 

  Be careful of the cutting attachment!   

 
Residual risks 

Even  if  you  use  this  tool  correctly,  there  are  always  residual  risks.  The  following  hazards  may  arise  in 

connection with the structure and manufacture of this power tool: 

-

 

Hearing impairment if no suitable hearing protection is worn. 

-

 

Cuts if no suitable protective clothing is worn. 

-

 

Health damage resulting from vibration in the hands and arms if the device is used for a long period of 

time or is not handled and maintained properly. 

-

 

Inhalation of particles 

-

 

Inhalation of exhaust gases 

-

 

Skin contact with oil / gasoline 

-

 

Inhalation of gasoline / oil vapors 

-

 

Contact with projected objects 

-

 

Burns when touching with hot surfaces 

-

 

Prolonged use of this product exposes the operator to vibration and can produce so-called "white finger" 

disease. To reduce the risk, wear gloves and keep your hands warm. 

-

 

If any of the symptoms of "white finger syndrome" occur, seek immediate medical attention. Symptoms 

of the "white finger" include numbness, loss of sensitivity, tingling, pain, loss of strength, color changes or 

skin condition. These symptoms usually appear on the fingers, hands or wrists. Risk increases at low 

temperatures. 

 
Intended use 

This machine can be used with the cutting wire as a trimmer for cutting grass and weeds of small thickness 

and in small quantity and with the cutting blade as a brush cutter for cutting denser vegetation. This machine 

must  not  be  used  for  cutting  or  other  cutting  operations  where  the  cutting  tool  must  be  lifted  above  the 

ground.  This  machine  is  only  authorized  for  private  use.  Any  other  use  or  modification  of  this  machine  is 

prohibited and involves high risks.

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for RACD314TB

























Reviews: