RACOM RAy3-11 User Manual Download

Page: 177 / 241

6.2. Working with CLI

• Overview of CLI options

cli_help

Fig. 6.1: CLI menu

• Parameters of CLI commands are listed in the help. For example:

help listing

-h

target unit

-t

local, default option

-t l

both, both units, command item for remote unit has PEER_ prefix

-t b

peer, opposite unit, when reading using the show command

-t p

• When inserting commands, using the tabulator can help

• An incorrect command is rejected (e.g. inserting forbidden frequency)

• A parameter that caused the loss of the connection is restored after 1 minute (Rollback)

• Reading parameters of local unit

cli_cnf_show

• Reading radio parameters of peer unit

cli_cnf_show -t p | grep RADIO

• Entering parameters (TX power of local unit)

cli_cnf_set RADIO_TX_PWR=-3

Items of command (RADIO_TX_PWR=) are taken from the list cli_cnf_show

177

Command Line Interface

Summary of Contents for RAy3-11


















































































































































































































































Search results

Summary of Contents for RAy3-11

Reviews:

Related manuals for RAy3-11

Brands by name

Popular brands

RACOM RAy3-11, User Manual

Search results

Summary of Contents for RAy3-11

Reviews:

Related manuals for RAy3-11

Brands by name

Popular brands