Setting end points
�����
EU declaration of conformity
W
arranty terms and conditions
����������������������������� Illustrations not binding.
RADEMACHER
Geräte-Elektronik GmbH
Buschkamp 7
46414 Rhede (Germany)
info@rademacher.de
www.rademacher.de
Service:
Hotline 01807 933-171*
Fax +49 2872 933-253
service@rademacher.de
* 30 seconds free of charge,
subsequently 14 cents/
������������
line networks and max.
42 cents/minute from
German cellular networks.
or loading factory settings
Manufacturer
Exiting settings
2.
Move the roller shutter in
the desired direction
with
button 1
.
Recommendation
First in the up direction.
3.
In addition press/tap
button 2...
4.
Release button 2 again
as soon as the desired end
point is reached.
5.
You can adjust the end
point in small steps by
briefly pressing button 2.
6.
������������
direction of travel after
successfully setting the
end points.
The respective end point
is stored.
Direction of
travel 1
or
Direction of
travel 2
twice briefly and
press and hold
the third time.
Set the rocker
switch to the
centre position.
II
I
III
III
III
II
I
Only RolloTube S-line
1.
First switch on button 3
(continuous phase).
RolloTube C/M and S-line
ON/
SET
The LED on
button 3 must
light up
continuously.
Continue with point 2.
Only RolloTube S-line
7.
������������
phase.
ON/
SET
Exiting end point setting, see next column.
RADEMACHER Geräte-Elektronik GmbH hereby
declares that the universal setting cable complies
with the Directives
2014/30/EU (EMC Directive)
and
2014/35/EU (Low Voltage Directive)
.
Conformity has been verified. The corresponding
declarations and documentation are available on file
at the manufacturer’s premises.
RADEMACHER Geräte-Elektronik GmbH
Buschkamp 7
46414 Rhede (Germany)
RADEMACHER Geräte-Elektronik GmbH provides a 24 month
warranty for new equipment installed in accordance with the in-
stallation instructions. All construction faults, material defects and
manufacturing defects are covered by the warranty.
Your statutory warranty claims remain �����by this warranty.
The following are not covered by the warranty:
◆
����������������
◆
Non-observance of the installation and operating manual
◆
Improper operation or wear and tear
◆
�����������������������������
◆
Repairs and �������
by third parties, unauthorised persons
◆
Use of unsuitable accessories
◆
Damage caused by inadmissible excess voltages
(e.g. lightning strikes)
◆
Operational malfunctions caused by radio frequency overlap-
ping and other such radio interference
A prerequisite for the warranty is that the new device must have
been purchased from one of our approved specialist retailers.
Proof of this must be provided by presenting a copy of the
invoice.
RADEMACHER will remedy any defects that occur within the
warranty period free of charge either by repair or by replacement
������������������������������
or one to the same value. There is no general extension of the
original warranty period by delivery of a replacement or by repair
as per the terms of the warranty.
Only RolloTube S-line
1.
First switch on button 3
(continuous phase).
The LED on
button 3 must
light up
continuously.
Continue with point 2.
RolloTube C-/M- and S-line
2.
Connect both directions of
Switch
button 1
to any position
and
simultaneously
press
button 2
.
travel to the mains supply
for approx. 5 seconds until
the tubular motor confirms
this by briefly running up
and down.
After that the factory
settings are loaded.
II
I
ON/
SET
or
III
Exiting end point setting / factory settings
1.
Remove the mains plug from the socket.
2.
Disconnect the motor connecting cable.
3.
Reconnect the tubular motor to the mains.
◆
After the end point setting
�����������������������������
respective operating manual.
◆
After loading the factory settings
Restore the original tubular motor connection.
Stop pressing button 2,
switch off the specified
direction of travel (button 1
into centre position) and
button 3.
I IIII
Set the rocker
switch to the
centre position.
III
ON/
SET
