background image

8

R1KR 28 - RAD - ING - Manual - 1807.1_SK.2_MIAB3013_R7_PDX

1 Av

ve

rte

nze

 gener

ali pe

r l'in

stall

azione
_L

oca

le ca

ldaia

_c

ond

_luogo 
pa

rz. prot
_E

N

1. INSTALLATION  

INST

ALLER

1.1. INSTALLATION

1.1.1. GENERAL INSTALLATION 

WARNINGS

 ATTENTION

This machine may be used only for the 

purpose for which it has been designed: heat water 
to a temperature below boiling point at atmospheric 
pressure. Any other use is considered wrong and 
dangerous. The manufacturer is excluded from 
any contractual or out of contract responsibility for 
damage caused to people, animals or property due 
to errors during installation.

 ATTENTION

This boiler should be installed only 

by qualified personnel, having the appropriate 
technical training in the field for the installation and 
maintenance of components of civil and industrial 
domestic hot water production and heating plants.

 ATTENTION

After having removed the packing, make 

sure the equipment is intact. In case of doubt, do not 
use the equipment and contact the supplier.

BEFORE INSTALLING THE BOILER, THE 
INSTALLER MUST MAKE SURE THAT THE 
FOLLOWING CONDITIONS ARE MET:

 

› The device is connected to a heating plant and a 

water supply network appropriate for its power 
and performance.

 

› The  location  must  be  properly  vented  through 

an air vent.

 

› The air vent must be placed at floor level to 

prevent it from being obstructed, protected by 
a grid that does not hamper the useful section 
of passage.

 

› The device is suitable for use with the type of 

gas available by checking the boiler data plate 
(placed on the inner side of the front casing.

 

› Make sure that the tubes and couplings are 

perfectly sealed, without any gas leaks.

 

› Make sure that the grounding system works 

properly.

 

› Make sure that the electrical systems is 

suitable for the maximum power absorbed by 
the equipment, value indicated on the data plate.

 WARNING

Use only original RADIANT optional or kit 

accessories (including electrical).

1.1.2. BOILER LOCATION 

ENVIRONMENTAL 
REQUIREMENTS

The device's installation location should be vented 
due to the presence of threaded joints on the gas 
adduction line. The location should be therefore 
provided with vents as to ensure air exchange, 
with output grid in the natural accumulation area 
of eventual gas losses.

 WARNING

DO NOT install the boiler in a technical 

compartment near a swimming pool or a laundry, to 
avoid that the combustion air is exposed to chlorine, 
ammonia or alkaline agents that may worsen the 
corrosion phenomenon of the heat exchanger. Failure 
to observe this caution will void the warranty of the 
heat exchanger.

THIS BOILER HAS BEEN DESIGNED FOR OUTDOOR 
INSTALLATION IN A PARTIALLY PROTECTED 

Summary of Contents for R1KR 28









































































Reviews: