background image

Wing center section

DO NOT try to fly an out-of-balance model !

29- Balance 

5-13/64” (132mm)

 Note: If necessary, move the battery pack or add weight to either the tail
 or nose until the correct balance is achieved.

Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. 
Peel off one corner of the backing and cut off with scissors. 
Arrange sticker on model and when satisfied adhere the corner without backing.
Carefully peel back the rest of the backing while at the same time adhering the rest of the sticker.

Try not to make air bubbles, if there are some, carefully puncture sticker (center of bubble) but not model 
surface with the tip of the knife or sharp pin and squeeze out the air. 
At curves stretch sticker and apply a little heat so that no ceases occur. 
Cut off the excess that is produced.

28- Decor

All details are subject to change
without notice !

Technische Anderungen und Irrtumer
vorbehalten !

IMPORTANT:

Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner 
to clean on surface of your model to keep the colour not fade.

FUELS

FUELS

CHAMPION

A E R O S P A C E

Summary of Contents for P-51 VooDoo
















Reviews: