background image

STICK

SPORT

90

90 Class - 2 Cycle engine

120 Class - 4 Cycle engine

Radio control model  -  RC Flugmodell

SPECIFICATIONS

Wingspan                                       1940mm
Length                                            1460mm
Electric Motor          1000 Watt (BOOST 90)
Glow Engine                  15cc 2-T / 20cc 4-T
Radio                          5 Channel / 5 Servos

TECHNISCHE DATEN

Spannweiter                                  1940mm
Lange                                            1460mm
Elektroantrieb         1000 Watt (BOOST 90)
Verbrennerantrieb         15cc 2-T / 20cc 4-T
Fernsteuerung                5 Kanal / 5 Servos

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

INSTRUCTION MANUAL / Montageanleitung

Summary of Contents for Stick Sport 90











Reviews: