background image

14

4

'%14&+0)

"

#

"4/

9

#;

"

2

*10'

"

%

108'45#6+10

You can record both sides of a 
conversation on any phone connected 
to the same phone line as the system. 

#

At any time during the conversation, 
hold down

 2 WAY

 until 

h(ý

h(ý

h(ý

h(ý

appears on the 

display. The system starts recording. 
Press 

2 WAY

 again to stop recording. 

The recording number flashes on the 
display until you play the conversation. 

2

.#;+0)

"

/

'55#)'5

1

/

'/15

1

6

91

/

9

#;

"

2

*10'

"

%

108'45#6+105

The number of messages flash after 
the system records new messages, 
recorded memos, or two-way phone 
conversations.

1. To listen to all messages, memos, 

and two-way conversations, press 

PLAY/PAUSE

. The system plays 

each new message in sequence 
and announces the day and time it 
was recorded. After playing all new 
messages, the total number of 
messages appears on the display 
and the system saves the 
messages. 

±

±

±

±

#

"

+/2146#06

"

#

Every state has different 
regulations governing 
the recording of 
conversations over the 
telephone. To determine 
that your use is in 
compliance with such 
laws or guidelines, 
check your local, state, 
and federal laws before 
using this product to 
record any telephone 
conversation.

±

"

016'

"

±

"

If there are no 
messages, the 
system beeps twice 
when you press 
PLAY/PAUSE.

Each message is 
treated as a new 
message until you 
play it back in its 
entirety.

Operation

Summary of Contents for 14 Minute





















Reviews: